ShoreTel SA-100 Installation Manual Download Page 72

Page: 72 / 84

SA-100 Planning, Installation, and Administration Guide

Chapter 7: Maintenance

Figure 7-5

Switch Connectivity panel

The Switch Connectivity panel includes the following:

•

Connectivity Grid:

The following indicators provide information about the

listed switch/appliance:
— Green (C) indicates that the switch/appliance is connected and

communicating with other switches/appliances in the system.

— Yellow (U) indicates that the switch/appliance connectivity is unknown

because it cannot communicate with TMS.

— Red (N) indicates that the switch/appliance has lost communications with

the server.

For more detailed information about a switch/appliance, place the mouse cursor

over the connectivity cell in question and status information is displayed in the

status bar at the bottom of your browser.

7.4

Audio and Web Conferencing Activity

The Service Appliances Maintenance Screen shows the number of ports currently

being used for audio and Web conferencing, the number of available ports allocated

for conferencing and the overall load on the appliances at each site in the system.

Summary of Contents for SA-100





















































































Search results

Summary of Contents for SA-100

Reviews:

Related manuals for SA-100

Brands by name

Popular brands

ShoreTel SA-100, Installation Manual

Search results

Summary of Contents for SA-100

Reviews:

Related manuals for SA-100

Brands by name

Popular brands