ShoreTel SA-100 Installation Manual Download Page 31

Page: 31 / 84

Chapter 4: Site Requirements and Preparation

SA-100 Planning, Installation, and Administration Guide

ShoreTel 12.3

The SA-100 provides two methods of fault tolerance. To protect against Ethernet

switch failure, connect Ethernet ports GB1 and GB2 to separate Ethernet switches. To

protect against port or cable failure, connect LAN1 and LAN2 to separate ports on the

same Ethernet switch.

4.5

Maintenance Cable

The ShoreTel SA-100 provides a maintenance port that you can connect a terminal to

using a DB-9, female-to-female, null-modem connector. You can use the

maintenance port to assign the unit IP address parameters when DHCP is not used.

4.6

Environmental Requirements

To ensure optimum operating conditions for the ShoreTel Service Appliance 100,

verify that the operating environment is adequately ventilated, free of gas or

airborne particles, and isolated from electrical noise.

Summary of Contents for SA-100





















































































Search results

Summary of Contents for SA-100

Reviews:

Related manuals for SA-100

Brands by name

Popular brands

ShoreTel SA-100, Installation Manual

Search results

Summary of Contents for SA-100

Reviews:

Related manuals for SA-100

Brands by name

Popular brands