Sharp UX-D1200SE Operation Manual Download Page 83

Page: 83 / 104

Problems and Solutions

. T

roub

le-

shooting

Dialing is not possible.

• Make sure the power cord is properly plugged into a

power outlet.

• Make sure that the telephone line is properly

connected to both the

TEL. LINE

jack and the wall

jack (see page 15).

• Make sure that the machine is set to the correct

dialing mode for your telephone line. See the
procedure on page 69 and “DIAL MODE” on page 70.

The power is on, but no
transmission takes place.

• Make sure that the receiving machine has paper.

• If the receiving machine is in manual mode with no

attendant, reception will not be possible.

• Check the display for error messages.

• Pick up the handset and check for a dial tone. Dial the

receiving machine manually and make sure that it is
responding (you should hear a fax tone).

Nothing is printed at the
receiving end.

• Make sure that the document for transmission is

placed face down in the feeder.

A distorted image is
received at the other end.

• Noise on the telephone line may cause distortion. Try

sending the document again.

• Make a copy of the document on your machine. If the

copy is also distorted, your machine may need
service.

Reception and copying problems

Problem

Solution

The machine doesn't
receive documents
automatically.

• Make sure that the reception mode is set to AUTO.

Summary of Contents for UX-D1200SE









































































































Search results

Summary of Contents for UX-D1200SE

Reviews:

Related manuals for UX-D1200SE

Brands by name

Popular brands

Sharp UX-D1200SE, Operation Manual

Search results

Summary of Contents for UX-D1200SE

Reviews:

Related manuals for UX-D1200SE

Brands by name

Popular brands