Sharp UX-D1200SE Operation Manual Download Page 57

Page: 57 / 104

Sending a Fax: Auto Dialing

4. Sending

Redial

You can automatically redial the last
number dialed on the machine.

Load the document(s).

•

If desired, press

to set the

resolution and/or contrast.

Press

once. Make sure the

display shows the number you wish
to dial.

If you are sending a fax, press

Dialing begins.
If you are making a phone call, lift
the handset. Dialing begins.

Note:

If the transmission is

unsuccessful and [

DOCUMENT

JAMMED

] appears in the display,

remove the document as explained on
page 88.

RESOLUTION/

RECEPTION MODE

Automatic redialing

If you use auto dialing (including Direct
Keypad Dialing) to send a fax and the
line is busy, the machine will
automatically make three redial
attempts at intervals of five minutes.

During this time, [

RECALLING

] will

appear in the display, followed by the
attempt number. You will not be able to
dial any other locations while the
message appears.

♦

To clear the message and stop

automatic redialing, press

Under certain conditions, automatic
redialing may stop before three
redialing attempts are made.

STOP

Summary of Contents for UX-D1200SE









































































































Search results

Summary of Contents for UX-D1200SE

Reviews:

Related manuals for UX-D1200SE

Brands by name

Popular brands

Sharp UX-D1200SE, Operation Manual

Search results

Summary of Contents for UX-D1200SE

Reviews:

Related manuals for UX-D1200SE

Brands by name

Popular brands