SEPTENTRIO Altus NR2 User Manual Download

Page: 38 / 81

9.2. USING THE USB CONNECTION

9.2 Using the USB connection

9.2.1 Connecting the USB data cable for the ﬁrst

time

The USB drivers for the Altus NR2 can be installed by following the steps below:

•

Make sure the computer is connected to the internet.

•

Connect the Altus NR2 to a USB port of your computer using the USB cable.

•

A new drive called ‘Altus NR2’ will appear in the File Explorer after a few seconds. Pop-

ups may appear indicating that drivers are being installed but these should be ignored.

•

In the folder ‘driver’, you will ﬁnd an executable driver ﬁle. Right click on this ﬁle and

select ‘Run as administrator’ as shown in Figure 9-2.

Figure 9-2:

Run the executable driver installation ﬁle in the folder ‘driver’

•

For the ﬁnal stage of the driver installation, you will be prompted to disconnect then

reconnect the USB cable from your pc as shown in Figure 9-3.

Summary of Contents for Altus NR2


















































































Search results

Summary of Contents for Altus NR2

Reviews:

Related manuals for Altus NR2

Brands by name

Popular brands

SEPTENTRIO Altus NR2, User Manual

Search results

Summary of Contents for Altus NR2

Reviews:

Related manuals for Altus NR2

Brands by name

Popular brands