Sencore VB330 User Manual Download Page 107

Page: 107 / 203

6.8.1.3

Ethernet — FSM — Syslog

The VB330 has a built-in syslog server which captures all incoming messages (UDP, port 514). Messages

are displayed in a pageable grid with the following columns: Facility, Severity, Timestamp, Hostname,

Agent and Message. Currently displayed page can be exported as an XML-document.

Since the syslog server typically stores about 100 pages of messages there is a group of buttons for a
fast navigation:

Newest

Move to the first page

Much newer

Move 10 pages backwards

Newer

Move 1 page backwards

Older

Move 1 page forwards

Much older

Move 10 pages forwards

Oldest

Move to the last page

Syslog server has a limited capacity which is usually enough to store the latest 10,000 messages
depending on the size of the syslog messages. When a new message arrives and no storage space
remains the oldest messages are removed.

Note that the syslog server is very sensible to time settings, so it is strongly recommended to have a time
synchronization enabled.

VB3xx 10G Probe User’s Manual version 5.3

107

Summary of Contents for VB330












































































































































































































Search results

Summary of Contents for VB330

Reviews:

Related manuals for VB330

Brands by name

Popular brands

Sencore VB330, User Manual

Search results

Summary of Contents for VB330

Reviews:

Related manuals for VB330

Brands by name

Popular brands