manualshive.com logo in svg

Sencore VB330, User Manual

Share
Download
Sencore VB330 User Manual Download Page 19

STAT:

Green status LED for future use

MANAGEMENT:

The green LEDs indicate link and activity. A blinking LED indicates activity, whereas

a steadily lit LED indicates link without activity (traffic). If the left LED is active the
speed is 10/100Mbps, the right LED indicates 1000Mbps.

LINK:

Green LED indicating SFP link status

ACT:

Green LED indicating SFP activity (traffic)

4.6

Installing the Unit in a Rack

The following equipment is needed for hardware installation of the unit:

•

4 rack screws

•

A screw driver for the rack screws

•

For rear mounting: a size 2 Phillips screwdriver for rack ear screws

4.6.1

Default Installation — Connectors at the Front of Rack

By default the Enhanced chassis is shipped with rack ears for front mounting of the unit. The rack ears
are designed to support the weight of the unit, so no additional support, like a rack shelf, is needed.

When deciding where to locate the unit, make sure there is sufficient space surrounding the unit to allow

efficient cooling, refer to section 4.2.2.

Use four rack screws to install the unit in the rack.

4.6.2

Optional Installation — Connectors at the Rear of Rack

For rear mounting of the chassis, the rack ears should be moved prior to rack installation. Unscrew the
six size 2 Phillips screws holding the rack ears, and move the six screws covering the rear mounting
holes to the front mounting holes. Remount the rack ears at the rear end of the unit.

Install the unit as described in section 4.6.1.

4.6.3

Optional Installation — Mid-Mounting

The Enhanced Chassis allows rack ears to be mid-mounted. This can be convenient if the chassis is

installed in a telco environment. Unscrew the six size 2 Phillips screws holding the rack ears, and move

VB3xx 10G Probe User’s Manual version 5.3

19

Summary of Contents for VB330












































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands