SeeMeCNC Artemis 300 Assembly Manual Download Page 38 | Manualshive

Page: 38 / 40

background image

Step 50 — Perform Initial Power Up and Function Test

At this time we will wait to install the two covers. We will perform the initial power up and check
functions before buttoning up. For the sake of continuity though, we have included the installation
of the covers in this guide. So, read about it now so you can install it later, or came back later for
the correct installation procedure.



Plug in the power cable to printer.



Turn the printer on.



The hot end should light up, as well as the status LEDs on the Duet board.



We will now move on to the initial connection and setup. NOTE: We will install the base & top
cover when complete.



Go Here Next >

Configuring Artemis



Assembling Artemis 300

© 2018

seemecnc.dozuki.com/

Page 38 of 40

«
...
36
37
38
39
40
»

Summary of Contents for Artemis 300









































Reviews:

No comments

Related manuals for Artemis 300

iPF710 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 92

iPF8000S - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

IMAGERUNNER 7095 PRINTER

Brand: Canon Pages: 615

Brand: QMS Pages: 86

634dte - X B/W Laser

Brand: Lexmark Pages: 148

5550N - Phaser B/W Laser Printer

Brand: Xerox Pages: 16

Brand: Ouring Pages: 54

ApeosPort C6550 I

Brand: Xerox Pages: 132

Brand: DataMetrics Pages: 35

Brand: DataMetrics Pages: 37

C11CA19201 - WorkForce 30 Color Inkjet Printer

Brand: Epson Pages: 36

C11CA19201 - WorkForce 30 Color Inkjet Printer

Brand: Epson Pages: 3

C11C694201 - PictureMate Dash PM 260 Color Inkjet Printer

Brand: Epson Pages: 72

C11C638001 - LQ 300+II B/W Dot-matrix Printer

Brand: Epson Pages: 120

C11C640001 - LX 300+II B/W Dot-matrix Printer

Brand: Epson Pages: 129

C11CA54203 - PictureMate Show Digital Frame

Brand: Epson Pages: 106

C11CA19201 - WorkForce 30 Color Inkjet Printer

Brand: Epson Pages: 2

Brand: Epson Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands