Rev.3.0 del 13/06/2016
ELECTRONIC PANEL
LRX 2035 Compact
Mono-phase electronic control unit for the automation of sliding
doors and rolling shutters with incorporated radio receiver.
- Mod.
LG 2035 Compact
: Without Radio Receiver
- Mod.
LRS 2035 Compact
: 433,92 Mhz
- Mod.
LRS 2035 SET Compact
: 433,92 Mhz “narrow band”
- Mod.
LRH 2035 Compact
: 868,30 Mhz “narrow band”
TECHNICAL DATA:
- Power supply : 230 Vac 50Hz 2.5W max.
- Flashing light output : 230 Vac 50Hz
100W Resistive Load max.
50W Inductive Load max.
- Motor outputs : 230 Vac 50Hz 500 W max.
- Aux. power supply output : 24 Vac 1.5 W max.
- Button and safety device input : 24 Vdc
- Working temperature : -10
÷
55 °C
- Radio receiver : see model
- Op. transmitters : 12-18 Bit, or Rolling Code
- Max. TX codes in memory : 7
- Dimension of panel : 99x50x28mm.
- Container : ABS V-0 ( IP44 internal use ).
CONNECTIONS OF THE TERMINAL BOARD:
CN1 :
1 : 230 Vac input (Phase).
2 :230 Vac input (Neutral)
3 :230 Vac flash input (Neutral)
4 : 230 Vac flash input (Phase).
5 :Opening motor output
6 :Common motor output.
7 :Closing motor output.
CN2:
1 :24 Vac 1.5 W service power supply output.
2 :24 Vac 1.5 W service power supply output.
3 :Open-close push button control input (NA).
4: Common GND input.
5 :Safety device input (NC).
6 :Aerial earth input.
7 :Aerial hot pole input.
OPERATING FEATURES:
Step-by-step operation:
By using both the radiocontrol ( LED CODE on ) and the low
voltage push button panel (
PUL ) to activate the fastening, the
following functioning is obtained:
the first command impulse activates the opening
mechanism until time expiry of the timing motor. The
second command impulse closes the frame. If an
impulse is sent before time has expired, the control
unit will
stops
the motion.
A further input implements the re-starting of the motion in the
opposite direction.
Automatic closing:
The control unit closes the frame automatically without sending
other commands.
Choice of this operating mode is described under the instruction
for setting the Pause time.
Safety device:
The control unit allows for the connection and control of
Photocells, Tyre sensors (NC).
Command from these devices are ignored during opening whilst
the gate is closing they will reverse the direction of movement.
Important:
If not used the terminals must be jumped.
Operation using different Models of Radio Control
Different models of radio control may be programmed: by
storing one code (1 button) a cyclic step by step operation (Up -
Stop - Down) is achieved, and by storing two different codes (2
buttons) separate commands are created, one for upward
movement and one for downward movement. Storing a BeFree
series radio control (3 buttons) produces three separate
commands: the first button is used for upward movement, the
second for Stop and the third for downward movement.
18 Operation using a 1-button radio control:
The following type of operation is obtained using a radio control
with a single button: the first press controls the upward
movement of the shutter until the motor timer stops. The second
press controls the downward movement of the shutter. If the
button is pressed before the motor stops running, the control
unit will stop the shutter moving and the button will need to be
pressed again to reactivate the motor in the opposite direction.
19 Operation using a 2-button radio control:
The following type of operation is obtained using a radio control
with 2 buttons: the first button (“Up”, corresponding to upward
movement) controls upward movement until the motor stops
running and the second button (“Down”, corresponding to
downward movement) controls the downward movement of the
shutter. If the upward movement is interrupted with another “Up”
command, the motor will continue to run in its upward
movement direction. If, however, the movement is interrupted
with a “Down” command, the control unit will stop the motor.
The procedure remains the same for the downward movement
phase.
Operation using a 3-button radio control (BeFree x1):
The following type of operation is obtained using the BeFree x1
radio control: the (Up) button controls upward movement until
the end of the motor running time, the (Stop) button causes all
movement to stop and the (Down) button controls downward
movement. If a Stop command is sent during upward or
downward movement, the control unit causes this movement to
GB
