SeaDoo Rotax 1503 4-Tec 2005 Page 56 Engine Shop Manual Download

Page: 56 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 04 (LUBRICATION SYSTEM)



WARNING

Wear safety glasses and work in a well
ventilated area when working with strong
chemical products. Also wear suitable non-
absorbent gloves to protect your hands.

– Remove oil suction pump cover with oil separa-

tor housing and his cover.

NOTE:

On the supercharged intercooled engine,

the oil suction pump cover and oil separator is a
one-piece design.
– Remove oil strainer

no. 12

R1503motr120A

TYPICAL — NATURALLY ASPIRATED AND
SUPERCHARGED ENGINES

1. Oil strainer

R1503motr370A

TYPICAL — SUPERCHARGED INTERCOOLED ENGINE

1. Oil strainer

Cleaning and Inspection

Clean oil strainer with a part cleaner then use an
air gun to dry it.



WARNING

Always wear eye protector. Chemicals can
cause a rash break out in and an injury to your
eyes.

Inspect rubber rings

no. 13

and

no. 14

R1503motr121A

TYPICAL — NATURALLY ASPIRATED AND
SUPERCHARGED ENGINES

1. O-ring
2. Rubber ring gasket

R1503motr371A

TYPICAL — SUPERCHARGED INTERCOOLED ENGINE

1. Gasket
2. Rubber ring gasket

If rubber rings are brittle, cracked or hard, replace
them.

SMR2005-035

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands