SeaDoo Rotax 1503 4-Tec 2005 Page 63 Engine Shop Manual Download

Page: 63 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 04 (LUBRICATION SYSTEM)

R1503motr133A

TYPICAL — NATURALLY ASPIRATED AND
SUPERCHARGED ENGINES

1. Ventilation hose

R1503motr374A

SUPERCHARGED INTERCOOLED ENGINES

1. Ventilation hose

– Disconnect wiring harness from OSPS

no. 9

and TOPS valve

no. 8

– Detach intake hose from throttle body (naturally

aspirated engine only).

– Remove other required parts from vehicle to

access the oil suction pump housing.

– Remove retaining screws

no. 10

and

no. 11

– Place rags under cover to prevent spillage. If

spillage occurs, clean with the pulley flange
cleaner (P/N 413 711 809).



WARNING

Wear safety glasses and work in a well
ventilated area when working with strong
chemical products. Also wear suitable non-
absorbent gloves to protect your hands.

– Remove the oil suction pump cover with oil sep-

arator housing and his cover.

NOTE:

On the supercharged intercooled engine,

the oil suction pump cover and oil separator is a
one-piece design.
– Remove oil pump screws

no. 27

and cover

no. 28

R1503motr135A

TYPICAL

1. Oil pump cover

– Remove oil pump shaft ass'y

no. 29

– Remove outer rotor

no. 30

SMR2005-035

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands