manualshive.com logo in svg

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual, Page: 54 / 124

Share
Download
SeaDoo Rotax 1503 4-Tec 2005 Engine Shop Manual Download Page 54

Section 01 ENGINES (1503 4-TEC)

Subsection 04 (LUBRICATION SYSTEM)

F18D2ZA

1

INSTALLATION AT CYLINDER HEAD

1. Remove this plug and install gauge here

Start engine and read pressure at different RPM
as per following table.

OIL PRESSURE

MEASURED AT CYLINDER

HEAD LOCATION

1503 4-TEC NATURALLY ASPIRATED ENGINE

ENGINE RPM

PRESSURE kPa (PSI)

Idle (cold)

296 - 400 (43 - 58)

for a very short time

Idle (at 80°C (176°F)

Min. 138 (20)

4000 - 7500

172 - 241 (25 -35)

ALL 1503 4-TEC SUPERCHARGED ENGINES

Idle (cold)

400 - 497 (58 - 72)

for a very short time

Idle (at 80°C (176°F)

Min. 138 (20)

4000 - 7500

172 - 241 (25 - 35)

Reinstall plug.

PTO OIL STRAINER

NOTE:

The oil strainer does not need to be

cleaned at every oil change. Clean it during other
inspections, especially when the engine is disas-
sembled.

Removal

Remove:
– engine oil (refer to OIL CHANGE in the appro-

priate

VEHICLE SHOP MANUAL

)

– PTO cover

no. 5

(refer to PTO COVER/MAGNE-

TO section)

– oil strainer

no. 6

.

1

R1503motr117A

1. Oil strainer

Cleaning and Inspection

Clean oil strainer with a part cleaner then use an
air gun to dry it.

WARNING

Always wear eye protector. Chemicals can
cause a rash break out in and an injury to your
eyes.

Check and clean the oil outlet area for dirt and
other contaminations.

46

SMR2005-035

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Reviews:

No comments