SeaDoo Rotax 1503 4-Tec 2005 Page 48 Engine Shop Manual Download

Page: 48 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 03 (PTO HOUSING AND MAGNETO)

R1503motr56A

TYPICAL

1. Starter drive bearing

R1503motr45A

TYPICAL

1. Starter drive support

CAUTION:

Be sure not to forget the distance

washer, disc springs and washer on the starter
drive shaft when assembling.

OIL SPRAY NOZZLE

Supercharged Engines Only

Removal

Remove the PTO housing as described above:
– Turn oil spray nozzle

no. 23

by using a grip plier

to crack the Loctite.

CAUTION:

Do not try to pull out the oil spray

nozzle with a plier. This may damage the force
fit in the PTO housing.

– Fix supercharger spray nozzle remover tight on

oil spray nozzle.

R1503motr264A

1. Oil spray nozzle
2. Spray nozzle remover

– Remove oil spray nozzle carefully by using a

slide hammer puller.

Installation

For installation, reverse the removal procedure.
However, pay attention to the following.

Apply Loctite 648 (P/N 413 711 400) on oil spray
nozzle fitting surface.

CAUTION:

The oil spray nozzle must be in ex-

act position to supply enough oil to the super-
charger. Any other installation will lead to a su-
percharger damage.

Only use supercharger spray nozzle installer to
push in the nozzle

no. 23

. Use retaining screw

hole to ensure the exact position.

R1503motr265A

1. Spray nozzle installer
2. Screw hole for positioning

smr2005-032

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands