SeaDoo Rotax 1503 4-Tec 2005 Page 104 Engine Shop Manual Download

Page: 104 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 07 (CYLINDER BLOCK)

Ring End Gap

RING END GAP mm (in)

NEW MINIMUM

RECTANGULAR

TAPER-FACE

OIL SCRAPER RING

0.35 (.014)

NEW MAXIMUM

RECTANGULAR

TAPER-FACE

OIL SCRAPER RING

0.50 (.020)

SERVICE LIMIT

ALL

1 (.04)

Measure position for ring end gap in the area of 8
to 16 mm (.315 to.630 in) from top of cylinder.

NOTE:

In order to correctly position the ring in the

cylinder, use piston as a pusher.

Using a feeler gauge, check ring end gap. Replace
ring if gap exceeds above described specified tol-
erance.

Installation

For installation, reverse the removal procedure.
Pay attention to the following details.

Install the oil scraper ring first, then the taper-face
ring with the word “TO” facing up, then the rect-
angular ring with the word “T” facing up.

A31C2NA

1. Rectangular ring
2. Taper-face ring
3. Oil scraper ring

CAUTION:

Ensure that top and second rings are

not interchanged

NOTE:

Use a ring expander to prevent breakage

during installation. The oil ring must be installed
by hand.

Check that rings rotate smoothly after installation.

Space the piston ring end gaps 120° apart and do
not align the gaps with the piston pin bore or the
thrust side axis.

A31C2OA

1. DO NOT align ring gap with piston trust side axis
2. DO NOT align ring gap with piston pin bore axis
A. 120°

CRANKSHAFT

Crankshaft Locking

Remove:
– intake manifold (refer to INTAKE MANIFOLD

AND SUPERCHARGER section)

– fuel rail cover
– spark plugs
– plug screw.

SMR2005-037

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands