SeaDoo Rotax 1503 4-Tec 2005 Page 61 Engine Shop Manual Download

Page: 61 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 04 (LUBRICATION SYSTEM)

Using a vernier depth gauge, measure side wear
as shown.

R1503motr131A

1. PTO housing surface
2. Vernier depth gauge

R1503motr132A

1. Oil pump outer rotor surface
2. Vernier depth gage

Difference between pump housing and outer rotor
should not exceed 0.1 mm (.004 in). If so, replace
the complete oil pump assembly.

NOTE:

When the axial clearance of the oil pump

shaft assembly increases, the oil pressure de-
creases.

Check the inside of oil pump housing and its cover
for scoring or other damages and replace if dam-
aged.

Installation

For installation, reverse the removal procedure.
Pay attention to the following details.

NOTE:

Never use oil in the press fit area of the

rotary seal.

Push coolant/oil pump shaft seal in place by using
thumb.

R1503motr128A

1. Oil seal

Install the new rotary seal by using the rotary seal
pusher (P/N 529 035 823).

529036014

CAUTION:

Never use a hammer for the rotary

seal or coolant/oil pump shaft installation. On-
ly use a press to avoid damaging the ceramic
component.

SMR2005-035

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands