SeaDoo Rotax 1503 4-Tec 2005 Page 101 Engine Shop Manual Download

Page: 101 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 07 (CYLINDER BLOCK)

F00B09A

1. Use the micrometer to set the cylinder bore gauge
2. Dial bore gauge

F00B0AA

TYPICAL

1. Indicator set to 0 (zero)

Position the dial bore gauge 62 mm (2.44 in) above
cylinder base, measuring perpendicularly (90°) to
piston pin axis.

Read the measurement on the cylinder bore
gauge. The result is the exact piston/cylinder wall
clearance.

PISTON/CYLINDER CLEARANCE mm (in)

NEW NOMINAL

0.024 to 0.056

(.0009 to.0022)

SERVICE LIMIT

0.090 (.004)

NOTE:

Make sure used piston is not worn.

If clearance exceeds specified tolerance, rehone
cylinder sleeve and replace piston ass'y by an
oversize one.

NOTE:

It is not necessary to have all pistons re-

placed with an oversize if they are not all out of
specification. Mixed standard size and oversize
piston are allowed.

NOTE:

Make sure the cylinder bore gauge indica-

tor is set exactly at the same position as with the
micrometer, otherwise the reading will be false.

Piston Pin

Using synthetic abrasive woven, clean piston pin
from deposits.

Inspect piston pin for scoring, cracking or other
damages.

Measure piston pin. See the following illustration
for the proper measurement positions.

Piston Pin/Connecting Rod Bearing Clearance

Measure inside diameter of connecting rod.

CONNECTING ROD SMALL END

DIAMETER mm (in)

NEW MINIMUM

23.01 (.9059)

NEW MAXIMUM

23.02 (.9063)

SERVICE LIMIT

23.07 (.908)

R610motr73A

1. Bore gauge
2. Connecting rod

SMR2005-037

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands