SeaDoo Rotax 1503 4-Tec 2005 Page 37 Engine Shop Manual Download

Page: 37 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 02 (INTAKE MANIFOLD AND SUPERCHARGER)

F19D0CA

4-TEC SUPERCHARGED ENGINES

1. Cable position in bracket
2. Cable barrel position in cam

Supercharger

Supercharged Engines

Sealing surface between supercharger and PTO
housing has to be greased with Super Lube grease
(P/N 293 550 030).

R1503motr247A

1. Super Lube grease

Install supercharger ass'y on PTO housing. Ap-
ply Loctite 243 (P/N 293 800 060) on the retaining
screws.

Torque screws to 10 N•m (89 lbf•

To tighten and torque the upper screw, use the
Torx adapter (P/N 529 035 938).

F00B20A

Ensure to install the tool perpendicularly (90°) to
torque wrench to apply the proper torque to the
screw.

F00B1UA

1. Tool perpendicular (90°) to torque wrench
A. 90°

CAUTION:

Not installing the tool as shown will

change the torque applied to the screw. Proper
torque and tightening sequence are important.

After complete installation of the supercharger,
the slipping moment has to be rechecked. Re-
fer to SUPERCHARGER CLUTCH SLIPPING MO-
MENT above in this section.

Finalizing the Installation

Readjust throttle cable and reset the TPS using the
VCK. Refer to ENGINE MANAGEMENT section of
the appropriate

VEHICLE SHOP MANUAL

SMR2005-033

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands