SeaDoo Rotax 1503 4-Tec 2005 Engine Shop Manual Download Page 41 | Manualshive

Page: 41 / 124

SeaDoo Rotax 1503 4-Tec 2005 Engine Shop Manual Download Page 41

Section 01 ENGINES (1503 4-TEC)

Subsection 03 (PTO HOUSING AND MAGNETO)

PTO HOUSING REMOVAL

Place rags under PTO housing to prevent spillage.
Up to 250 mL (8 oz) of oil could flow out when re
moving PTO housing. If spillage occurs, clean im-
mediately with the pulley flange cleaner (P/N 413
711 809) to prevent oil stains.

Disconnect CPS and magneto from wiring har-
ness.



WARNING

Always disconnect battery or starter cables
exactly in the specified order, BLACK negative
cable first. Disconnect electrical connections
prior to disconnecting fuel lines.

Slightly lift rear part of engine and safely block in
this position. Remove rear LH side engine sup-
port

no. 1

.

1

R1503motr50A

TYPICAL

1. Engine support

Remove:
– thru-hull fitting boot

1

F18J0BA

2

1. Thru-hull fitting boot
2. Remove this collar

– coolant pump housing

no. 2

(refer to COOLING

SYSTEM)

– screws

no. 3

and

no. 4

NOTE:

Carefully separate the PTO housing from

the engine using two flat screwdrivers prying
equally at the same time. Proceed slowly so that
starter gear disc springs

no. 6

and washer

no. 7

do not fall down.
– PTO housing

no. 5

CAUTION:

Ensure to use prying lugs to sepa-

rate PTO housing to prevent damaging contact
surface.

32

smr2005-032

www.SeaDooManuals.net

«
...
39
40
41
42
43
...
»

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Reviews:

No comments