SeaDoo Rotax 1503 4-Tec 2005 Page 112 Engine Shop Manual Download

Page: 112 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 07 (CYLINDER BLOCK)

R1503motr22A

1. Thrust washer
2. Sealing surface

Install cylinder block lower half. Refer to CYLIN-
DER BLOCK in this section.

Install the crankshaft cover before mounting the
engine bracket. Apply oil on O-ring and press cov-
er in. Crankshaft cover has to be flush with cylin-
der block surface.

R1503motr19A

1. O-ring
2. Crankshaft cover

CAUTION:

Install

crankshaft

locking

tool

(P/N 529 035 821) right away to position crank-
shaft at TDC before installing the camshaft and
rockers (refer to CYLINDER HEAD).

529035821

R1503motr18A

1. Crankshaft locking tool

CYLINDER BLOCK

Disassembly

Remove:
– engine oil (refer to OIL CHANGE in the appro-

priate

VEHICLE SHOP MANUAL

)

– engine from vehicle (refer to the appropriate

VE-

HICLE SHOP MANUAL

)

– cylinder head (refer to CYLINDER HEAD sec-

tion)

– PTO housing (refer to PTO HOUSING/MAGNE-

TO section)

– starter gear (refer to PTO HOUSING/MAGNETO

section)

– starter drive ass'y
– oil suction pump with oil separator cover (refer

to LUBRICATION section)

– balancer shaft (refer to BALANCER SHAFT else-

where in this section)

– crankshaft (refer to CRANKSHAFT elsewhere in

this section)

– piston with connecting rod (refer to PISTON/

CONNECTING ROD elsewhere in this section).

SMR2005-037

107

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands