SeaDoo Rotax 1503 4-Tec 2005 Page 108 Engine Shop Manual Download

Page: 108 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 07 (CYLINDER BLOCK)

R1503motr41A

1. Dial gauge
2. Crankshaft

CRANKSHAFT AXIAL CLEARANCE mm (in)

NEW MINIMUM

0.08 (.003)

NEW MAXIMUM

0.22 (.009)

SERVICE LIMIT

0.35 (.014)

Installation

For installation, reverse the removal procedure.
Pay attention to following details.

NOTE:

Before installing the crankshaft, make

sure that the timing chain is on the crankshaft and
the chain guide has been installed first. Those
parts cannot be installed when the crankshaft is
in place.

CAUTION:

Crankshaft

and

balancer

shaft

marks have to be aligned.

R1503motr17A

1. Mark on balancer shaft
2. Mark on crankshaft

For correct installation of the connecting rods, re-
fer to PISTON/CONNECTING ROD in this section.

CAUTION:

It is absolutely necessary to follow

this procedure. Otherwise severe engine dam-
age can occur.

CAUTION:

Never forget thrust washers no. 4

on center of crankshaft to control axial adjust-
ment.

Insert thrust washers as soon as crankshaft is in
place as per following illustration.

R1503motr09A

THRUST WASHER INSERT DIRECTION

1. Thrust washer

CAUTION:

Thrust washers have to be flush

with the cylinder block sealing surface.

SMR2005-037

103

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands