GENERAL INFORMATION
GENERAL FEATURES
SWING2 control unit has been deigned in order to manage one or two swing operators without limit switch. Its dimensions are
very small, four different operation modes, possibility to adjust many parameters using the trimmer and dip switch, in addition
the possibility to manage the use of the encoder through the safety gate device.
The absolute news of such electronic unit consists in two different learning modes of working times. Besides the
standard and intuitive selflearning mode of working times (the same for GATE2), it gives the possibility to learn
MANUALLY the working times, acting simply on TRIMMER Rv4 ADJUSTMENT.
TECHNICAL FEATURES
Control unit power supply
Transformer
Absorbed power
Max. motor charge
Max. accessories charge
Max. flashing light charge
Environment temperature
Protection fuses (24V accessories)
Programming modes
Operating logics
Opening / closing time
Pause time
Thrust force
Slowdowns
Leaf delay
Encoder sensitivity
Connecting terminal entries
Connecting terminal exits
Board dimensions
Outside box features
SETTING
For the security of persons it is important to follow with attention all the advises and instructions in this manual. A
wrong installation or a wrong use of the product can cause sever dammages to persons.
Make sure that the installation has an adeguate differential switch as prescribed by the law in force and provide on the power
supply net a magnetothermic omnipolar switch. For the installation of the electric cables use adeguate rigid and/or flexible
tubes.
Keep always separate the connection cables of low voltage accessoires from those of 115/230V~ power supply. To avoid any
interference use separate casings.
2
Max. Length of the power supply cable between control unit and motors is 10m, using cables with 2,5 mm section.
SWING 2
24
ACCESSORES TECHNICAL FEATURES
Kind of accessories
I
nom
absorbed (
stand by)
SIGNAL receivers
15 mA each
PHOTO 50
55 mA each couple
PHOTO 60
108 mA each couple
GHOST 40
60 mA each couple
GHOST 50
60 mA each couple
SLIM
95 mA each couple
Kind of accessories
I
nom absorbed
(stand by)
KEY PLUS START-STOP
10 mA
CODE + MODULE DEC.
12 mA
CODE PLUS
6 mA
THERMO
15 mA
LOOP
16 mA
RADIODEC PROX
150 mA
NOTE: the sum of the nominal power absorbed by the each accessory on 24V exit must not exceed 200 mA.
English
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
REV 07 - 05/2009
230V ~ (+6 -10%) - 50/60 Hz
P1: Vn=230V , Io=43.3 mA; S1: Vnom=17.5V , Vo=20.2V , I=0.69A
7,5 W
500 W x 2
24V 200mA
230V 50W max.
-20°C +50°C
1 A
Selflearning page 31; instructions
manual including TRIMMER page 34
Automatic / Semi-automatic / safety automatic / safety Semi-
automatic
Adjustable with trimmer until 120 sec.
Adjustable with trimmer from 0 to 120 sec.
Adjustable with trimmer
Adjustable with trimmer
Selflearning mode during programming phase.
During working times mode adjustable with trimmer
Only during selflearning mode,
Adjustable with trimmer
Antenna / Stop / Start / pedestrian Start /
photocells 1 and 2 / Encoder 1 and 2
Power supply accessories 24V / Motors 230V 500W x 2 /
Flashing light 230V 50W / Electric lock 12V 15VA max/
TX photocell power supply 24V / Capacitor
150,7 x 141 x 47,5 mm
305 x 225 x 125 mm - Ip55
~
~
~
~
