background image

WARNINGS

The electric installation and the functioning logic choice must agree with the laws in force. In any case you must 
foresee a 16A and threshold 0.030A differential switch. Keep the power cables (motors, power supply) separate 
from the command cables (push buttons, photocells and so on). In order to avoid any interference it’s preferable to 
foresee and use two separate sheaths.

REPLACEMENTS

Any request for spare parts must be sent to: 
     

SEA s.r.l. - Zona Ind.le, 64020 S.ATTO - Teramo - Italia

USE DESTINATION

The electronic equipment   23001135 has been designed to be used exclusively as management equipment for 
sliding gates automation, swing gates, sectional doors, overhead doors, barriers.

SAFETY AND ENVIRONMENTAL COMPATIBILITY 

It’s recommended not to dispel in the environment the packaging materials of products   and/or circuits.

STORING

Materials handling must be made with appropriate vehicles..

DISINSTALLATION  AND MAINTENANCE

The disinstallation and/or putting out of service and/or maintenance of the electronic equipment 23001135 must be 
made only and exclusively by authorized and qualified staff.

WARRANTY LIMITS

The warranty form of the electronic equipment 23001135 is valid for 24 months starting from the printed date on the 
product. The mentioned product will be considered under warranty if it doesn’t show any damage caused by an 
irregular use or by any modification or breaking. The warranty is   valid only for the original buyer.

NOTE:THE MANUFACTURER IS NOT CONSIDERED RESPONSIBLE FOR EVENTUAL DAMAGES CAUSED 
BY IRREGULAR, WRONG OR UNREASONABLE USE.

SEA reserves the right to make any required modification or change to the products and/or to this manual without 
any advanced notice obligation.

REGULAR PRODUCT DISPOSAL (electric and electronic   waste)

(It’s   applicable in UE countries and in those ones provided with a differential rubbish collection)

The brand that you find on the product or on documentation signals that the product must not be disposed off 
together with other domestic rubbish at the end of life cycle. In order to avoid any possible environmental or health 
damage because of the irregular waste disposal, we kindly invite you to separate this product from other kind of 
rubbish and to recycle it in a responsible way in order to favor the sustainable reuse of material resorces. Domestic 
users are invited to contact the retailer where the product has been purchased or the local office in charge for all the 
information related to defferential   collection and recycling of this kind of product.

WAREHOUSING TEMEPERATURES

T

min

T

Max

 

Dampness

min

 

Dampness

Max

- 40°C

+ 85°C

5% 

not condensing

90% 

not condensing

WARNINGS AND WARRANTY

SWING 2

English

38

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

REV 07 - 05/2009

Summary of Contents for SWING 2




















Reviews: