Scientific SMO1002 Page 96 User Manual Download

Page: 96 / 102

Prompting Messages and Troubleshooting

A) Prompting Messages:

■

Trig level at limit! :

Mention you that the trigger Level is at a limit when you turn the Trig level knob.

■

Horizon position at limit! :

Mention you that the horizontal position is at a limit when you turn the

horizon position knob.

■

Volts/Div at limit! :

Mention you that the vertical voltage have already touched the Min 2

V/div or the

Max 10V/div.

■

Volts position at limit! :

The system would display this information when the vertical position is at a

limit.

■

Sec/Div at limit! :

Prompts that the Volts/Div is at full range while turning the vertical scale knob.

■

Holdoff time at limit! :

Turn the “Universal” knob when holdoff time has been to max or min value, now

the system will clew this information.

■

Functions isn’t useable! :

Under several special modes, the some functions could not be running.

■

No signal! :

The system would clew this information when the signal could not match the auto set

condition. (Using in the auto set)

■

Adjust at limit! :

You could adjust the pulse width by the universal knob till the pulse width has reached

min20.0ns or max 10.0s.

■

Location Empty! :

If you have no stored waveforms or setups on some location, the screen will display

this information when you press the “Recall” button on this location.

■

USB Flash Drive Plug In! :

This information will appear when you invert the USB Flash Drive to the

USB Host port.

■

USB Flash Drive Pull Out! :

This information will appear when you pull out the USB Flash Drive.

■

Store Data Success! :

Save setup data, waveform data or picture data to the internal of the

oscilloscope or USB flash successful.

■

Ready Data Success! :

Read setup data or waveform data from the

internal of the oscilloscope or

USB flash successful.

■

Please set Back USB to printer! :

Press the “S/div” knob will appear this information on the screen

when the “Print Key” option is set to “Print Picture” and the “Back USB” option is set to “USBTMC”.

■

USB Flash Drive isn’t connected! :

When the “Save To” option is set to “File” or the “Print Key” option

is set to “Save Picture” in “Save/Recall” menu , Press the “Save” option button or the “S/div” knob before

inverting the USB Flash Drive to the USB Host port will appear this information on the screen.

■

Record Wave Success! :

This message will appear when you finish recording waveforms.

B) Troubleshooting

1. After the oscilloscope is powered on the screen remains dark, please do steps as follows

■

Check the power cable’s connection.

■

Ensure the power switch is turned on.

User Manual SMO702, SMO1002

Summary of Contents for SMO1002







































































































Search results

Summary of Contents for SMO1002

Reviews:

Related manuals for SMO1002

Brands by name

Popular brands

Scientific SMO1002, User Manual

Search results

Summary of Contents for SMO1002

Reviews:

Related manuals for SMO1002

Brands by name

Popular brands