Scientific SMO1002 Page 85 User Manual Download

Page: 85 / 102

10. Press the “Y Mask” button; turn the “Universal” knob to adjust the vertical clearance.

11. Press the “Create Mask” button to create mask and you also can enter the next page of “Mask menu”

to recall the stored mask.

12. Enter the second page of “Pass/Fail function menu”, press the “Output” option button to set the

output option.

13. Enter the first page of “Pass/Fail function menu”, press the “Operate” option button to select “ ”to run

the pass/fail test.

h) Waveform Record

Waveform record can record input waveform from CH1 and CH2 with a maximum record length of 2500

frames. This record behavior can also be activated by the pass/fail test output, which makes this function

especially useful to capture abnormal signals in long term without keeping an eye watching it. Waveform

recorder: Record the waveforms with specified interval.

Fig. 73 Pass Fail Setup Page 1

Table 61: Waveform recorder function menu

User Manual SMO702, SMO1002

Summary of Contents for SMO1002







































































































Search results

Summary of Contents for SMO1002

Reviews:

Related manuals for SMO1002

Brands by name

Popular brands

Scientific SMO1002, User Manual

Search results

Summary of Contents for SMO1002

Reviews:

Related manuals for SMO1002

Brands by name

Popular brands