Scientific SMO1002 Page 86 User Manual Download

Page: 86 / 102

To record waveforms, follow these steps:

1. Press the UTILITY button to enter “Utility menu”.

2. Press the “Next Page” option button to enter the third page of “Utility menu”.

3. Press the “Record” button to enter “Waveform Record Menu”.

4. Press the “Mode” option button to select “Record”.

5. Press the “Source” option button to select the input signal channel.

6. Select “Interval” option, turn the “Universal” knob to adjust time interval between record frames.

7. Select “End Frame”, select the “Universal” knob to adjust the max record frame.

8. Press “ ”in “Operate” option to record waveform.

Play Back: Play back current record waveforms or saved record waveforms.

Fig. 74 Waveform Record Function 1

Table 62: Waveform play back function menu 1

User Manual SMO702, SMO1002

Summary of Contents for SMO1002







































































































Search results

Summary of Contents for SMO1002

Reviews:

Related manuals for SMO1002

Brands by name

Popular brands

Scientific SMO1002, User Manual

Search results

Summary of Contents for SMO1002

Reviews:

Related manuals for SMO1002

Brands by name

Popular brands