www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
28
GB
•
Insert the jackleg (19) into the opening (26c) at
the pick-up point (G) (Fig.26) and secure it with
the fastening pin and the split pin (B6) (Fig. 27).
The depth of the jackleg can be adjusted in various
positions.
Plow function (Fig. 8/29/32)
Fasten the wheel mountings (I) as shown in fig. 28.
•
Grease the tool shaft (3g) and pay attention to the
alignment of the mounting hole (3i) (Fig. 3) when in-
stalling the wheels (K).
1) Insert the fastening pins large (B6) into the openings
and secure them with the split pins.
2) Attach the plow (J) to the desired height using a fasten-
ing pin and split pin (B6) as shown in fig. 32.
Adding engine oil
Check the engine oil lever.
Failure to fill engine sump with oil before starting engine
will result in permanent damage and void engine warran-
ty (see Engine operator´s manual ).
Adding transmission oil
Check the transmission oil level.
The gearbox can be permanently damaged and the gear-
box warranty will be extinguished if the gearbox is not
filled with oil before starting (see chapter “Maintenance
& cleaning”).
Refueling
m
WARNING!
Always wear protective gloves when per-
forming maintenance.
This product is powered by a 4 stroke engine.
Store unleaded gasoline in a clean container approved
for gasoline.
Recommended fuel:
This engine is certified to operate on unleaded gasoline
intended for automotive use with an octane rating of 91
or higher.
Never use stale or contaminated gasoline or an oil/gas-
oline mixture. Avoid getting dirt or water in the fuel tank.
m
WARNING!
Follow safety instruction for fuel handling.
Always shut off engine before fuelling. Never add fuel to
a machine with a running or hot engine. Move at least 3
m from refuelling site before starting engine.
DO NOT
SMOKE!
1.
Clean surface around fuel cap to prevent contamina-
tion.
2.
Loosen fuel cap slowly.
3. Carefully pour fuel into the tank. Avoid spillage.
4.
Prior to replacing the fuel cap, clean and inspect the
gasket.
5. Immediately replace fuel cap and hand tighten.
Wipe up any fuel spillage.
m
WARNING!
Check for fuel leaks, if any are found, cor-
rect before use. Contact a Servicing Dealer if necessary.
8. Function
Clutch lever (3)
The forward movement of the blades is carried out by pulling
the lever upwards. The machine is stopped by releasing it.
Throttle trigger (2)
It controls the motor speed. Pulling the throttle lever in the
directions shown makes the engine run faster or slower.
Jackleg / Working depth regulator (19)
It´s for setup of the working depth. The jackleg supports
the operator in the direction and speed regulation of the
ground hook.
By lowering the depth setting the ground hook would be
braked and the working depth would be increased. By lift-
up the depth setting, the speed is faster and the working
depth would be reduced.
9. Operation
9.1 Adding fuel
Fill the fuel tank as instructed in the separate engine
manual.
9.2 Check-up before starting work
Adjusting the clutch (Fig.1)
m
CAUTION! THE POWER CULTIVATOR MUST NOT
ROTATE AT IDLE SPEED.
Serious injuries may occur when the cutting tool ro-
tates at idle speed.
m
ATTENTION!
Make adjustments on the clutch only by
authorized personnel!
Loosen the lock screw (1b).
To adjust the clutch, turn the adjusting screw screw (1a)
in the appropriate direction:
•
Counterclockwise to increase the tension of the clutch
cable,
•
Clockwise to reduce the tension of the clutch cable.
The tension of the clutch cable is sufficient as soon
as the clutch lever (3) engages into the locking clutch
lever (4) when released.
m
ATTENTION! Do not over-tighten the clutch!
After adjustment, tighten the lock screw (1b).
Damage to the clutch can cause the blades to rotate at
idle speed. This increases the risk of injury due to loss of
controllability and contact with the cutting tool.
9.3 Start the engine
m
ATTENTION!
When starting the engine, never pull the
clutch lever (3). Pulling the clutch lever (3) will accelerate
the engine, thereby rotating the machine’s milling tools
with the risk of accidents or injuries. Never wrap the start-
er cord around your hand.
