![background image](http://html1.mh-extra.com/html/sanden/vendo-vue-sxy-30/vendo-vue-sxy-30_manual_3859556040.webp)
P-8
Part #1167879 08/2008
4. Enter on Button 4 – ‘Testing in Progress’ – Hand should move to the Lock side of
the door.
5. Exit on Button 1.
6. Advance on Button 2 – ‘Go Opposite of Home’.
7. Enter on Button 4 – ‘Testing in Progress’ – Hand should move to hinge side of the
door.
8. Press Button 1 twice to exit – Test Motors X Motor.
Test Motors
Y Motor:
1. Still in Test Motors, Press Button 2 to scroll until “Y Motor” is displayed.
2. Enter on Button 4 – ‘Y Motor Go Home’
3. Enter on Button 4 – ‘Testing in Progress’ – Rail should move to the bottom of the
door.
4. Exit on Button 1
5. Advance on Button 2 – ‘Y Motor Go Opposite of Home’
6. Enter on Button 4 – ‘Testing in Progress’ – Rail should move to top of door
7. Exit on Button 1 twice – ‘Test Motors Y Motor’
Test Motors
Z Motor:
1. Still in Test Motors, Press Button 2 to scroll until “Z Motor” is displayed.
2. Enter on Button 4 – Calibration – Z Pos Z Cycle
3. Enter on Button 4 - Testing in Progress – Hand Clamp moves towards the shelves,
pauses momentarily, then retracts.
4. Exit on Button 1 twice – Test Motors Z Motor
*** Note – Do not apply pressure to the ‘Arm’ as it could potentially jam. Power down
vendor, wait 10 seconds, power on. Vendor should ‘Home’ any out of sync parts on
the arm.
Test Motors
Clamp Motor:
1. Still in Test Motors, Press Button 2 to scroll until “Clamp Motor” is displayed.
2. Enter on Button 4 – ‘Clamp Motor Clamp Open’
3. Enter again on Button 4 – ‘Testing in Progress’ – the Fingers on the Hand should
open
*** The Hand will not open if it is already open***
4. Exit on Button 1
5. Advance on Button 2 – ‘Clamp Motor Clamp Close’
*** The Hand will not close if it is already closed***
6. Enter on Button 4 – ‘Testing in Progress’ – The Fingers on the Hand Clamp should
close
7. Press Button 1 twice to exit
Test Motor
Get X Y Z Positions:
This is not applicable unless there is a problem. Please refer to the detailed instructions in the
‘Trouble Shooting Section’ of the SXY Manual.
Summary of Contents for Vendo Vue SXY 30
