T-4
Part #1167879 07/2008
ERROR
DESCRIPTION OF
ERROR CODE
CHECKING METHOD
CORRECTIVE
ACTION
Jam - Recovered
The unit encountered a jam
condition while vending. It
was able to recover from the
jam and return to home.
The
user was requested to select
a new product.
Check product positions to determine if any are sold out with
product still in column.
Complete a test vend cycle of sold out products. If hand hits tray
front, run Discovery 2. If hand jams on center gate, reduce Z Product
Position by 3 encodings.
Failed Movement
This is a non jam failure.
A
motor function failed to
complete.
Depends
on
movement
attempted.
If
Discovery
, check
reflectors.
Check Motors Movement in
T
est Mode and regular V
ending.
Check all Sensors under Check Sensor Status.
Install
any
missing
reflectors.
X-Rail
Not
Level
During a Discovery 2
operation, the X rail was
higher on one side by more
than 1 inch.
Unplug machine. Move the X rail manually to the center of the
machine
opposite
a
shelf.
Close
the
door
.
Look
along
the
bottom
of the rail at the trays. Determine which side is higher
.
Remove the X-rail cap. On the latch side of the machine, release the
Y
gear coupling. Move the X-rail down until it is level. Recheck. Run
Discovery 2.
FLO
Always
On
During a target search
operation, the Forward
Looking
Optic
(FLO)
was
found to be always active.
Test
Flo
with
a
corner-cube
reflector
piece.
The
device
has
two
lights.
The
green
light
should
be
on.
When
the
reflector
is
in
front
of the Flo, the second light should change from of
f to orange.
Check
reflectors
along
latch
side
trays.
FLO
may
have
only
seen
the
shelf
4
reflector
during
scan.
V
erify
X
Home
aligned
with
latch
side
reflectors.
If the green light is of
f, check the plug on the PDC. If the orange light
does
not
turn
on
and
of
f,
replace
the
FLO
assembly
.
If
the
Flo
does
turn
on and of
f replace the PDC board.
FLO
Always
Of
f
During a target search
operation, the Forward
Looking
Optic
(FLO)
was
found to never activate.
Check
power
on
the
FLO
device.
The
green
light
should
be
on.
Test
Flo
with
a
corner-cube
reflector
piece.
When
the
reflector
is in front of the Flo, the second light should change from of
f to
orange.
May
not
have
seen
any
reflectors
on
latch
side.
Check
reflectors
along latch side trays.
If the green light is of
f, check the plug on the PDC. If the orange light
does not turn on and of
f, replace the Flo assembly
. If the Flo does turn
on and of
f replace the PDC board.
Make sure door properly closed.
Missing Coordinates
During a Discovery operation,
an expected, required tray
reflector
was
not
found
1)
Check
reflectors
on
top
shelves.
2)
Check
all
reflectors
on
latch and hinge side trays are installed.
Install
any
missing
reflectors.
Check
power
on
the
FLO
device.
The
green
light
should
be
on.
Test
Flo
with
a
corner-cube
reflector
piece.
When
the
reflector
is
in
front
of
the
FLO,
the
second
light
should
change
from
of
f to
orange.
Check top and bottom shelves are properly seated on the base
metal.
If the green light is of
f, check the plug on the PDC. If the orange light
does
not
turn
on
and
of
f,
replace
the
FLO
assembly
.
If
the
Flo
does
turn
on and of
f replace the PDC board.
Reseat
tray
firmly
in
shelf
Missing
T
ray
Used in Discovery 3 and 4.
A
required tray is missing on
the top or bottom shelf.
Check
all
reflectors
on
top
and
bottom
shelves.
Install
any
missing
reflectors.
Shelf ends Mismatch
During a Discovery operation,
the number of shelves in the
latch side did not match the
shelves on the opposite side
of the machine.
Check all tray positions. Make sure each tray has a corner-cube
reflector
in
the
center
tray
pocket.
Replace
any
missing
tray
reflectors.
Run
Discovery
2.
Check all side trays are fully seated in shelves.
Reseat
tray
firmly
in
shelf.
Run
Discovery
2.
Shelf
Not
Level
During a Discovery operation,
one or more shelves was
found to vary in position more
than 1 inch from the hinge
side to the latch side.
Check all tray positions. Make sure each tray is fully seated on
the shelf.
Reseat
tray
firmly
in
shelf.
Summary of Contents for Vendo Vue SXY 30
