![background image](http://html1.mh-extra.com/html/sanden/vendo-vue-sxy-30/vendo-vue-sxy-30_manual_3859556125.webp)
T-11
Part #1167879 07/2008
ERROR
PROBABLE
CAUSE
CORRECTIVE
ACTION
Bill acceptor takes a bill but does not
establish credit.
Defective acceptor harness (credit not getting from
acceptor to control board through the harness).
Make sure that the acceptor and harnessing is correct for your style of
acceptor and it is plugged in and wired properly
.
Defective acceptor
.
Replace/test acceptor
.
Defective controller
.
Replace/test controller
.
Bill acceptor takes a bill and credits but not
erasing credit.
Defective bill acceptor
.
Replace acceptor and test acceptance and erasure of credit.
Defective controller
.
Replace/test controller for erasure of credit.
Both vend sensors are defective
Replace vend sensor
.
Acceptor takes a bill and allows payback of
coins without a selection.
Controllers
configurations
not
set
properly
.
Access
vendor
configuration
mode
and
check
the
“Forced
V
end”
setting.
VENDING PROBLEMS
Hand not in home postion
Communication error between VMC and PDC or
PDC software error
Cycle power to unit. Start-up routine should begin.
Hopper is open
V
end optics blocked
Enter
T
est Mode check V
end Detection (see service manual). Cycle power
to unit. Strat-up routine should begin.Relpace/T
est vend optics.
No vend upon selection.
No power or communication to hand.
Check
for
lights
on
hand.
Left
side
red
light
(motor
power)
right
side
flashing
(logicpower/
communication).
If
no
light
than
check
MDB
connection on VMC.
Hand not aligned correctly to tray when
vending.
T
ray or shelf out of position (not seated).
T
ray table
in the PDC not present or correct.
Reseat tray or shelf. Run calibration #1 then #2.
X-rail not moving, product in hand.
Vend
flap
motor
umpluged
or
linkage
broken.
Test
vend
flap
in
T
est
Mode.
Replace
if
broken.
Completely sold out while product is still in
the column.
Product pusher not functioning
Check to see if product pusher is engaged.
MISCELLANEOUS PROBLEMS
Door will not close completely
.
Hand assembley hitting the lower blukhead.
T
ri-T
eq
lock system is in the locked position.
Reposition y-rail stops and check y-home magnet. Open
T
ri-T
eq lock,
check for damage to lock slide.
Display shows sold out immediately upon
pressing selection button of full column (sold
out not clearing).
Door switch wired incorrectly or cut/pinched.
Manually press door switch. If still not vending, check wiring or replace
door switch.
Defective control board.
If door switch is replaced and still reading sold out, replace control board.
V
endor appears dead; no digital display and
no lights.
Defective main harness.
If red light on control board is of
f, check fuse and transformer
.
No digital display; vendor lights on.
Defective display or display harness.
Check display and display harness. Replace if necessary
.
Check
for
a
flashing
red
light
on
control
board.
If no light, replace control board.
V
endor scrolls message on display but does
not accept money
.
Changer out of tune.
See “T
uning Changer”.
Defective changer
.
Replace changer
.
Defective controller board.
Replace control board.
V
endor accepts money but does not display
credit.
Defective changer
.
Replace changer
.
Defective controller board.
Replace board.
Summary of Contents for Vendo Vue SXY 30
