Resolución de problemas
62
ENGLISH
ESPAÑOL
Troubleshooting
slow
fast
slow
no
slow
slow
slow
slow
the battery pack is almost discharged.
the battery pack is fully discharged.
When the remaining time of the
tape is about 3 minutes.
the tape reached its end.
there is no tape in camcorder.
the tape is protected to record.
the camcorder has some
mechanical fault.
moisture condensation has formed
in the camcorder.
Change to a charged one.
Change to a charged battery.
Prepare a new one.
Change to a new one.
Insert a tape.
If you want to record,
release the protection.
1. Eject the tape.
2. Set to OFF.
3. Detach the battery.
4. Reattach the battery.
* If repeated contact
local service.
see below.
2MIN
TAPE
END
TAPE
TAPE
C.EMG
D.EMG
L.EMG
R.EMG
DEW
Display Blinking
Informs that...
Action
- If the camcorder is brought directly from a cold place to a warm place,
moisture may condense inside the camcorder, on the surface of the
tape, or on the lens. In this condition, the tape may stick to the head
drum and be damaged or the unit may not operate correctly.
To prevent possible damage under these circumstances, the camcorder is
furnished with moisture sensor.
- If there is moisture inside the camcorder, “DEW” is displayed.
If this happens, none of the functions except cassette ejection will work.
Open the cassette compartment and remove the battery.
Leave the camcorder for at least two hours in a dry warm room.
Troubleshooting
- Before contacting a service center, perform the following simple checks.
They may save you the time and expense of an unnecessary call.
Moisture Condensation
Self Diagnosis Display
lento
la batería está casi descargada.
Cámbiela por una cargada.
rápido
la batería está completamente descargada. Cámbiela por una cargada.
2MIN
lento
el tiempo restante de la cinta es de
Prepare una nueva.
3 minutos aproximadamente.
TAPE
no
la cinta ha llegado al final.
Cámbiela por una nueva.
END
TAPE
lento
no hay ninguna cinta en la videocámara.
Inserte una cinta.
TAPE
lento
la cinta está protegida contra
Si desea grabar, quite la
grabación.
protección.
C.EMG
lento
la videocámara sufre alguna anomalía
1. Extraiga la cinta.
D.EMG
mecánica.
2. Coloque en OFF.
L.EMG
3. Desconecte la batería.
R.EMG
4. Vuelva a conectar la batería.
* Si se repite, póngase en con-
tacto con el servicio posventa.
DEW
lento
se ha formado condensación de
ver abajo.
humedad en la videocámara.
Visor
Parpadeo
Informa que…
Acción
- Si la videocámara pasa directamente de un lugar frío a uno cálido, se
puede condensar la humedad en su interior, en la superficie de la cinta o
en la lente. En estas condiciones, la cinta se puede enganchar al tambor
del cabezal y dañarse o puede que la unidad no funcione correctamente.
Para evitar daños, la videocámara está provista de un sensor de
humedad.
- Si hay humedad en el interior de la videocámara, se visualiza “DEW”. Si
ocurre esto, no se podrá utilizar ninguna de las funciones excepto la de
expulsión de la cinta. Abra el compartimento de la cinta y extraiga la
batería. Deje la batería durante un mínimo de dos horas en una habitación
cálida.
Resolución de problemas
- Antes de solicitar asistencia al servicio posventa, efectúe las comprobaciones
básicas siguientes. Pueden ahorrarle tiempo y el coste de una llamada innecesaria.
Condensación de humedad
Visor de diagnóstico automático