Samsung DW80M9* Series Service Manual Download

Page: 45 / 62

Troubleshooting_43

Item

Related

Parts

Symptoms

Description

n1: Version Display

When holding the following keys, the version displays alternating with "n1”:

- Normal Course Key: Sub PBA Version Display

- Heavy Course Key: Sub PBA Touch IC SW Version Display

- Delicate Course Key: Model Option Display

- Express (Quick) Key: Inverter PBA SW Version Display

- Rinse Key: WiFi Module Version Display

(Only for WiFi models; before receiving the version data, display “---“; display version if version information is received)

n2: Inspection Code

Display

- Each time Normal (Europe: Eco) Key is pressed, the code on display changes in a loop starting from the last saved code :

C00 → C10 → C20 → C30 → C40 → C50 → C60 → C00 → ...

- Up to 7 inspection codes can be saved, any additional code overwrites the oldest code.

※

Inspection codes are saved according to [Dish Washer - Inspection Mode - Inspection Recall Mode].

1. Each time Heavy Key is pressed while inspection code is on display, the information about the condition which triggers the

inspection code displays in sequence.

ex : When C00 displays, it changes as follows: C00 → C01 → C02 → C03 → C04 → C05 →C06 → ...

When C10 displays, it changes as follows: C10 → C11 → C12 → C13 → C14 → C15 → C10 → ...

※

CX1: X indicates the order of inspection code on display.

C01: indicates the code ID which occurs most recently.

2. When the operation button is held for 7 seconds with the inspection code on display, it clears all the inspection data.

n3: Smart Install

Auto

Mode Result Display

It determines based on the data saved in EEPROM.

- Smart Install Auto Mode is successfully completed: it is indicated by "OK"

- Smart Install Auto Mode is not successfully completed or not performed: it is indicated by "nG"

n4: Operation Cycle

Display

- The max. value is 9999 and it does not go any higher.

- When the finishing session is entered, Cycle Cnt increases unless Cancel & Drain has been enabled.

Summary of Contents for DW80M9* Series































































Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands

Samsung DW80M9* Series, Service Manual

Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands