Samsung DW80M9* Series Service Manual Download

Page: 50 / 62

48 _ Troubleshooting

Check type

Check code

Checking method

Corrective actions

Half load check

1. Check the connections for the Distributor Motor and Micro Switch

connectors.

- Reconnect the Distributor Motor and Micro

Switch connectors.

2. Check whether the coil in Distributor Motor is conductive.

: Remove the connectors before measuring.

► Normal: Approx. 3.6 ~ 4.0kΩ

- Faulty: Replace the Distributor Motor.

3. Check the position sensing operations when turning the Micro Switch on

and off.(Use n5 Service test mode.) Check the conduction between the

brown wire and the Violet wire.

► Micro switch On: Short

► Micro switch Off: Open

- Micro S

witc

h sign alters in ON/OFF state.

- It is NG if keep in ON or OFF state for 120 seconds.

* Do not supply with water and test.

- Faulty: Replace the Micro Switch for sensing

positions.

- Normal: Replace the valve distributor and

CAM switch.

4. Adjust Cam Assy and Find the faulty.

- Faulty: Replace Cam Assy.

5. Check whether half load is operating normally.

- Check the half load operation

► Normal: 110 ~ 120V

- Check the operation of Distributor Motor Relay.

: Check the operating voltage between the 3pin(Brown) wire of the

Main PBA CN401 connector and the 1pin(White) wire of the Main PBA

CN101 connector.

► Normal: 110 ~ 120V (while operating)

- Faulty: Replace the Main PBA Assy.

6. Check the Power Relay.

- See the “Power Relay check code”.

Summary of Contents for DW80M9* Series































































Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands

Samsung DW80M9* Series, Service Manual

Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands