Samsung DW80M9* Series Service Manual Download

Page: 41 / 62

Troubleshooting_39

4-2. SERVICE INSPECTION MODE

■ SVC Test mode

Item

Related

Parts

Symptoms

Description

Enable Smart Install

Mode

1) Set the timer for 17h with Power On.

2) Press Hi-Temp Wash Key for at least 7 seconds.

Disable Smart Install

Mode

- When Power Key is pressed, it is disabled with Power Off.

Smart Install Mode

Configuration

- There are Auto Mode and Manual Mode. When Smart Install Mode is enabled, it is set to Auto Mode by default.
- Mode change KEY : Changing modes can be done by entering the Auto Key while on standby or when the operation of each

mode has been completed. (AS → Manual mode STEP[1] → Manual mode STEP[2] → ... Manual mode STEP[7] → AS → ...

(Circulation))

- Entering the mode change KEY when the Door Open check code occurs will cancel the check code and go to the state where mode

change can be performed.

Smart Install Mode

Display

- Displays “AS” before Auto Mode is enabled.

- If Rinse Aid is not sufficient, Rinse Aid ICON turns on.
- During Auto Mode, the current Step No. blinks as an indication.

Auto Mode

Configuration

- Closing the Door within 3.7 seconds after entering the Start Key will automatically run Step 1 through to Step 6.

※

dC1 will occur if Door Open information is detected only in Inverter Micom. – If the Door opens during operation, it will stop and the

Door Open check code “dC(dC1)” will be displayed. However, this does not apply once Auto Door Open is activated. – When the

Door Open check code "dC(dC1)" is displayed, pressing the Start Key will turn the check code display off and it will re-run from the

initial AS.

1. During Auto Mode, all keys except Power Key are deactivated.

During Auto Mode, Sub Mode cannot be changed manually.

2. [Auto Mode STEP 1: check drainage and vane.]

3. Turn on the drain pump. (Use the following steps/ no drain error detection.)

- Drain pump on for 14 seconds → drain pump off for 2 seconds → drain pump on for 14 seconds → off for 5 seconds → complete

4. Move the vane back and forth while draining step is in progress.

(

※

Applicable to models with a vane only.)

5. Once the draining step completes and the vane operates normally, proceed to [STEP 2].

Summary of Contents for DW80M9* Series































































Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands

Samsung DW80M9* Series, Service Manual

Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands