Samsung DW80M9* Series Page 7 Service Manual Download

Page: 7 / 62

Features and Specifications _ 5

2. FEATURES AND SPECIFICATIONS

2-1. FEATURES

Features

Description

Remarks

Waterwall linear wash system

New Waterwall cleaning system gets dishes sparkling everytime

• High pressure, consistent wall of water cleans hard to reach places
• No need to pre-rinse
• Available on full or half cycle

Target zone washing

Targeted wash for hard to clean pots and pans

• Control water pressure, temperature and time
• Select left target zone

Half load cycle: upper and lower

Wash smaller loads without wasting water

• No need to wait until you have a full load
• Choose either upper or lower rack
• Saves on energy

Third rack with flex tray

Removable roll-up silverware tray for easy unloading

• Silverware lays flat for better cleaning
• Perfect for oversized or hard to fit items

• Easily roll up and remove for easy unloading

Adjustable racking system

Flexible design for more space

• Frees up more space on the top rack for tall and oversized items

Speed boost

Wash your dishes in less time

• Increased water pressure reduces wash time
• Perfect for everyday family dishes

Digital leakage sensor

Worry-free dishwashing

• Can sense a leak of only 1 1/2 ounces

• Shuts itself off before water can escape and cause floor damage

• Protects against water-related damage and provides peace of mind

Summary of Contents for DW80M9* Series































































Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands

Samsung DW80M9* Series, Service Manual

Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands