Samsung DW80M9* Series Service Manual Download

Page: 3 / 62

Safety Instructions _ 1

1. SAFETY INSTRUCTIONS

1-1. SAFETY INSTRUCTIONS FOR SERVICE ENGINEERS

ሪ

Make sure to observe the following instructions to operate the product correctly and safely and prevent possible

accidents and hazards while servicing.

ሪ

Two types of safety symbols, Warning and Caution, are used in the safety instructions.

Warning

Hazards or unsafe practices that may result in severe personal injury or death.

Caution

Hazards or unsafe practices that may result in minor personal injury or property damage.

Warning

Before Servicing

ࣃ

(When servicing electrical parts or harnesses) Make sure to disconnect the circuit breaker or power cable before

servicing.

- Failure to do so may result in a risk of electric shock.

ࣃ

Do not allow consumers to connect several appliances to a single power outlet at the

same time.

- There is a risk of fire due to overheating.

ࣃ

When removing the power cord, make sure to hold the power plug when pulling the plug

from the outlet.

- Failure to do so may damage the plug and result in fire or electric shock.

ࣃ

When the dishwasher is not being used, make sure to disconnect the circuit breaker or

power cable from the power outlet.

- Failure to do so may result in electric shock or fire due to lightning.

ࣃ

Do not place or use gasoline, thinners, alcohol, or other flammable or explosive substances near the dishwasher.

- There is a risk of explosion and fire caused from electric sparks.

Summary of Contents for DW80M9* Series































































Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands

Samsung DW80M9* Series, Service Manual

Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands