Samsung DW80M9* Series Service Manual Download

Page: 55 / 62

Troubleshooting_53

Check type

Check code

Checking method

Corrective actions

Power Relay

check code

None

1. Check the connections for the Power Relay connector

: Start the cycle by pressing the Power key. when measure the operating

voltage between the wires of the Power Relay and pin 1 wires of the

CN101.

Caution

Check the pin of the wires of the Power Relay and the Heater Relay.

► Normal: 110V ~ 120V

- Reconnect the Power Relay.

2. Check the door switch.

: Check the white wire and the switch connected to the white wire.

► W

hen

the door is open: The Door Switch is OFF.

► When the door is closed: The Door Switch is ON.

The Powe

r Relay and the Heater Relay use a 12V line.

If the switch is out of order, the Power Relay and the Heater Relay will not

operate.

- Faulty: Replace the Door Switch.

3. Check the driving signals for the power relay : Measure the voltage

between pin 7 and pin 2 of the CN402 connector on the main PBA.

► W

hen the door is open or before the cycle starts.

Normal: 1 V

► After the cycle has started by closing the door and pressing the Power

key. ". Normal : 10.5 to 13 V

- Faulty: Replace the main PBA Assy.

4. Check the operation of the Power Relay.

: Start the cycle by pressing the Power Key.

Measure the operation voltage between the terminal of the Power Relay

(pin 3) and pin 1 of CN101.

Caution

Check pin the Power Relay and pin 1 of CN101

► Normal: 110V ~ 120V

- Faulty: Replace the main PBA Assy.

Summary of Contents for DW80M9* Series































































Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands

Samsung DW80M9* Series, Service Manual

Search results

Summary of Contents for DW80M9* Series

Reviews:

Related manuals for DW80M9* Series

Brands by name

Popular brands