Samsung DB22D User Manual Download Page 112

Page: 112 / 159

Eco Solution

MENU

→

System

→

Eco Solution

→

ENTER

Eco Solution

Energy Saving

Screen Lamp Schedule

No Signal Power Off

Auto Power Off

Off

4 hours

The displayed image may differ depending on the model.

Energy Saving

Reduce the power consumption by adjusting the screen brightness.

•

Off

Low

Medium

High

Screen Lamp Schedule

Adjust the panel brightness. A value closer to 100 makes the panel brighter.

•

Off

No Signal Power Off

Save power by turning the device off when no signal is received from any source.

•

Off

15 min

30 min

60 min

―

Disabled when an attached PC is in power saving mode.

―

The product will automatically power off at a specified time. The time can be changed as required.

Auto Power Off

The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel
within select hours to prevent overheating.

•

Off

4 hours

6 hours

8 hours

Summary of Contents for DB22D
































































































































































Search results

Summary of Contents for DB22D

Reviews:

Related manuals for DB22D

Brands by name

Popular brands

Samsung DB22D, User Manual

Search results

Summary of Contents for DB22D

Reviews:

Related manuals for DB22D

Brands by name

Popular brands