Samsung DB22D User Manual Download Page 75

Page: 75 / 159

Gamma

MENU

→

Picture

→

Gamma

→

ENTER

Picture

Gamma

The displayed image may differ depending on the model.

Adjust the primary colour intensity.

―

Picture Mode

is set to

Calibration

Gamma

is disabled.

Calibrated value

MENU

→

Picture

→

Calibrated value

→

ENTER

Picture

Calibrated value

The displayed image may differ depending on the model.

Select whether to apply the brightness, colour, gamma and uniformity settings customized using the colour calibration
programme

Advanced Colour Management

to the Information and Advertisement modes.

•

Don't apply

Apply

―

To download the

Advanced Colour Management

programme, visit www.samsung.com/displaysolutions.

―

Picture Mode

is set to

Calibration

Calibrated value

is disabled.

Summary of Contents for DB22D
































































































































































Search results

Summary of Contents for DB22D

Reviews:

Related manuals for DB22D

Brands by name

Popular brands

Samsung DB22D, User Manual

Search results

Summary of Contents for DB22D

Reviews:

Related manuals for DB22D

Brands by name

Popular brands