Samsung DB22D User Manual Download Page 114

Page: 114 / 159

Device Manager

MENU

→

System

→

Device Manager

→

ENTER

Device Manager

Keyboard Settings

Mouse Settings

The displayed image may differ depending on the model.

Configure options for external input devices connected to the product.

Keyboard Settings

Configure keyboard connection settings or options for a connected keyboard.

Select Keyboard

Select a keyboard you want to use from the available connected keyboards.

―

It is possible to use only one connected keyboard.

Keyboard Options

―

Depending on the country.

Keyboard Language

Specify the keyboard input language.

Keyboard type

Specify the keyboard type.

Switch Input Language

Configure the key combination used to change the input language.

Summary of Contents for DB22D
































































































































































Search results

Summary of Contents for DB22D

Reviews:

Related manuals for DB22D

Brands by name

Popular brands

Samsung DB22D, User Manual

Search results

Summary of Contents for DB22D

Reviews:

Related manuals for DB22D

Brands by name

Popular brands