Samsung DB22D User Manual Download Page 88

Page: 88 / 159

Rotation

MENU

→

OnScreen Display

→

Rotation

→

ENTER

Rotation

Rotate menu

Rotate Content

Aspect Ratio

Landscape

Full Screen

The displayed image may differ depending on the model.

Rotate menu

Configure the menu screen.

•

Landscape

: Display the menu in landscape mode (default).

•

Portrait

: Display the menu in portrait mode on the right side of the product screen.

Rotate Content

Rotate the product screen orientation.

•

Landscape

: Display the screen in landscape mode (default).

•

Portrait

: Display the screen in portrait mode.

Aspect Ratio

Set the rotated screen to be either full screen or original.

•

Full Screen

: Display the rotated screen in full screen.

•

Original

: Display the rotated screen in the original aspect ratio.

―

Available only when

Rotate Content

is set to

Portrait

Summary of Contents for DB22D
































































































































































Search results

Summary of Contents for DB22D

Reviews:

Related manuals for DB22D

Brands by name

Popular brands

Samsung DB22D, User Manual

Search results

Summary of Contents for DB22D

Reviews:

Related manuals for DB22D

Brands by name

Popular brands