manualshive.com logo in svg

SAF CFIP PhoeniX C, Technical Description

Share
Download
SAF CFIP PhoeniX C Technical Description Download Page 86

 

86 

CFIP PhoeniX C Series TDM/IP Split Mount System Technical Description and Configuration Guide 

• 

Rev. 1.0 

•

 

© SAF Tehnika JSC 2013

 

priority queues are empty.

 

 

NOTE: 

QOS Mode configures egress policy (output  from switch) for  each port, whereas other QOS 

setting  modes  configure  ingress  port  policies  (input  to  switch).  Therefore  priority  assignment  is 
done at the input to the switch and function of queue controller is defined at the output from the 
switch. 

 

–

 

Priority policy

 – This drop-down menu defines the initial ingress queue policy. It defines the initial 

rules for what output queue will be assigned to every ingress frame.

 

- 

All

 – Next rules are used for priority assignment (from the top to the bottom order).

 

 

tagged IPv4/6 frames 

   

IQPRI = QPRI_T

 

   

FPRI = FPRI_T 

 

tagged non IPv4/6 frames 

   

IQPRI = QPRI_T

 

   

FPRI = FPRI_T 

 

untagged IPv4/6 frames 

   

IQPRI = QPRI_IP

 

   

FPRI = FPRI_IP

 

 

untagged non IPv4/6 frame

s

 

   

IQPRI = QPRI_D

 

   

FPRI = FPRI_D 

 

- 

Port only

 – Next rule is used for priority assignment.

 

 

all frame types 

   

QPRI = QPRI_D

 

   

FPRI = FPRI_D 

 
 

- 

Tagged  only

  –  Next  rules  are  used  for  priority  assignment  (from  the  top  to  the  bottom 

order).

 

 

tagged frames 

   

IQPRI = QPRI_T

 

   

FPRI = FPRI_T 

 

untagged frames 

   

QPRI = QPRI_D

 

   

FPRI = FPRI_D

 

 

- 

IPv4/6 only

  –  Next  rules  are  used  for  priority  assignment  (from  the  top  to  the  bottom 

order).

 

 

IPv4/6frames 

   

IQPRI = QPRI_IP

 

   

FPRI = FPRI_IP

 

 

non IPv4/6 frame

s

 

   

IQPRI = QPRI_D

 

   

FPRI = FPRI_D

 

 

–

 

Port  Priority  – 

The  configuration  of  default  port  priority.  Value  0  up  to  7  can  be  entered  (0  is 

default value) and it is then used for definition of FPRI_D and QPRI_D parameters according to 
the  above  described  figures.  The  next  possible  function  of  this  variable  is  a  definition  and/or 
replacement  of  QOS  priority  information  based  on  FPRI_D  for  frames  which  are  egressed  with 

Summary of Contents for CFIP PhoeniX C














































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands