manualshive.com logo in svg

SAF CFIP PhoeniX C, Technical Description

Share
Download
SAF CFIP PhoeniX C Technical Description Download Page 54

 

54 

CFIP PhoeniX C Series TDM/IP Split Mount System Technical Description and Configuration Guide 

• 

Rev. 1.0 

•

 

© SAF Tehnika JSC 2013

 

IP setting

 

 

Figure 34: IP address configuration – GUI page “IP / Address 

It  is  recommended  to  enter  basic  IP  configuration  of  local  and  remote  units  (IDUs)  at  the  very 
beginning.  This  step  is  necessary  for  proper  communication  between  local  and  remote  side  and 
optionally for ensuring remote access to IDU devices from customer´s network. In our example we use 
basic type of out-of-band management access (factory default configuration). Our examples suppose 
that remote IP access will be provided from the direction of LOCATION1_M. For this mode we have set 
following IP addresses: 

 

For link site with name LOCATION1_M

 

Primary IP / Mask = 192.168.3.201/24 
Default Gateway IP = 192.168.3.1 
Remote Unit IP = 192.168.3.211

 

 

For opposite link site with name LOCATION2_M

 

Primary IP / Mask = 192.168.3.211/24 
Default Gateway IP = 192.168.3.201 
Remote Unit IP = 192.168.3.201 

 

The remote device (IDU) must have equal IP addresses (primary IP and remote IP) set vice-versa. 
Select  in  your  web  browser  menu 

„IP / Address”

 

(Figure 34).  Enter  the  above  assigned  primary  IP 

address / net-mask, default gateway IP address and IP address of remote IDU on both sites. Confirm 
entered values by pressing APPLY button.

 

 

NOTE:

 It is necessary to assign just correct Primary IP and Remote Unit IP addresses for installation 

purposes. Informations from remote units cannot be displayed when this step is skipped.  Next IP 
settings can be applied during complete link configuration. 

 

Summary of Contents for CFIP PhoeniX C














































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands