manualshive.com logo in svg

SAF CFIP PhoeniX C, Technical Description

Share
Download
SAF CFIP PhoeniX C Technical Description Download Page 65

 

65 

CFIP PhoeniX C Series TDM/IP Split Mount System Technical Description and Configuration Guide 

• 

Rev. 1.0 

•

 

© SAF Tehnika JSC 2013

 

- 

off – 

This item (mode) disables aggregation function. The function in this mode is similar to 

function of design MULTI but with just three channels over air. 

–

 

TX Aggreg Mode 

–  This  drop-down  menu  sets  the  specific  Tx  aggregation  modes.  The  possible 

modes are: 

- 

auto 

–  TX  data  stream  is  automatically  divided  into  two  links  according  to    momentary 

available capacity of each link. 

- 

master only 

– Aggregation is disabled in this mode. TX data stream is manually directed to 

master link only. 

- 

slave only 

–  Aggregation  is  disabled  in  this  mode.  TX  data  stream  is  manually  directed  to 

slave link only. 

–

 

TX Aggreg Status  – 

This  box  shows  actual  TX  status  which  is  especially  important  for  auto 

aggregation mode. In this mode the aggregation block automatically decides what direction will 
be used for Tx data transmission: 

- 

aggregate – 

Data are transferred over both links (normal mode). 

- 

master only – 

Data are transferred over master link (slave link is down or in some trouble 

or mode is manually set to master only). 

- 

slave only – 

Data are transferred over slave link (master link is down or in some trouble or 

mode is manually set to slave only). 

–

 

RX Aggreg Mode 

– This box displays status of receiving part in an aggregation block: 

- 

ok – 

Receiving block operates properly, both traffic directions are aligned. 

- 

alignment drops  – 

Incorrect  order  of  packet  is  detected  at  receiving  side,  this  status 

indicates abnormal packet delay at master or slave link. 

- 

packet discards – 

This status indicates packet losses at master or slave link. 

–

 

Packet MUX Sync 

–  This  box  displays  actual  Packet  MUX  synchronization  at  master  and  slave 

unit. 

–

 

Fiber Optic Sync 

–  This  parameter  shows  actual  Fiber  Optic  interconnection  status  between 

master and slave unit. 

–

 

Device Status 

– This value shows alarm status of relevant unit.

 

 

Basic Link Info 

 

It  is  recommended  to  fill-in  the  table  with  complete  link  identification.  This  will  be  helpful  for  next 
system description. Such configuration is accessible from WEB GUI page 

„General / Info”

 in Figure 49. 

Summary of Contents for CFIP PhoeniX C














































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands