manualshive.com logo in svg

SAF CFIP PhoeniX C, Technical Description

Share
Download
SAF CFIP PhoeniX C Technical Description Download Page 31

 

31 

CFIP PhoeniX C Series TDM/IP Split Mount System Technical Description and Configuration Guide 

• 

Rev. 1.0 

•

 

© SAF Tehnika JSC 2013

 

Item 

Parameter 

Value 

EN 61000-3-2,3 

Safety 

IEC 60950-1/EN 60950-1 

 

Extension module CFIP-ASI-EXT 

Extension card CFIP-ASI-EXT (External Multiplexer Module) provides ASI extension for  CFIP Phoenix C 
Indoor Units. The CFIP-ASI-EXT card enables multiplexing up to four ASI channels into compact stream 
which is directed over fiber optic connection to/from CFIP Phoenix C IDU. The multiplexer features a 
basic unit with 4 x ASI built-in ports (one BNC per ASI channel) and 2 x SFP 1000Base-SX ports. 
The  compact,  simple  to  configure,  and  easily  scalable  design  enables  cascading  with  other  CFIP 
Phoenix  C  extension  devices  (e.g.  CFIP-16E1/T1-EXT).  The  configuration  is  performed  from  GUI  of 
Indoor Unit. 
The  real  overall  capacity  for  ASI  is  allocated  in  the  PBPS  based  on  true  selected  ASI  ports  in  GUI  of 
Indoor Unit. 
Priority Base Packet System (PBPS) is proprietary multiplexer system. 

 

 
 

CFIP-ASI-EXT Users ports 

Each ASI channel can be independently configured into Tx or Rx mode. Following port combinations 
are available by this setting 

 

- 

4x ASI Tx (unidirectional) 

- 

3x ASI Tx, 1x ASI Rx (bidirectional) 

- 

2x ASI Tx, 2x ASI Rx (bidirectional) 

- 

1x ASI Tx, 3x ASI Rx (bidirectional) 

- 

4x ASI Rx (unidirectional) 

 

Connectors on the CFIP-ASI-EXT front panel 

 

–

 

DVB ASI – 

four configurable I/O DVB-ASI ports (75 Ohm) 

–

 

SFP 1 UPLINK1

 

–

 master SFP port reserved for connection to IDU or to master Extension module 

card in Extension module chain 

–

 

SFP 2 UPLINK2 – 

slave SFP port reserved for connection to slave EMM card in Extension module 

chain or to relay IDU in add/drop configuration 

–

 

-48 VDC 

– power supply connector, + pole is grounded inside the device 

–

 

Grounding connector

 

Summary of Contents for CFIP PhoeniX C














































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands