Roland V-Card VC-1, Owner'S Manual

Page: 142 / 156

142
MIDI Implementation
❍
Portamento Time (Controller number 5)
Status 2nd byte 3rd byte
BnH 05H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Portamento Time: 00H - 7FH (0 - 127)
❍
Data Entry (Controller number 6, 38)
Status 2nd byte 3rd byte
BnH 06H mmH
BnH 26H llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = the value of the parameter specified by RPN/NRPN
mm = MSB, ll = LSB
❍
Volume (Controller number 7)
Status 2nd byte 3rd byte
BnH 07H vvH
n = MIDI channel number:0H - FH (ch.1 - 16)
vv = Volume:
00H - 7FH (0 - 127)
❍
Hold 1 (Controller number 64)
Status 2nd byte 3rd byte
BnH 40H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON
❍
Portamento Switch (Controller number 65)
Status 2nd byte 3rd byte
BnH 41H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
0 - 63 = OFF, 64 - 127 = ON
❍
RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte 3rd byte
BnH 65H mmH
BnH 64H llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are
extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in
any order) should be sent in order to select the parameter, then Data Entry
(Controller numbers 6 and 38) should be sent to set the value.
This device receives the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB Notes
00H, 00H mmH, llH Pitch Bender Range
mm: 00H - 0CH (0 - 12 semitones)
ll: ignored (processed as 00H)
Up to 1 octave can be specified in semitone
steps.
00H, 01H mmH, llH Fine Tuning
mm, ll: 00 00H - 40 00H - 7F 7FH
( -50 - 0 - +50 cent)
●
Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H - FH (ch.1 - 16)
pp = Program number: 00H - 3FH (prog.1 - prog.64)
* Not received when the Program Change Switch (SYSTEM MIDI) is OFF.
●
Channel Aftertouch
Status 2nd byte
DnH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Aftertouch Value: 00H - 7FH (0 - 127)
●
Pitch Bender Change
Status 2nd byte 3rd byte
EnH llH mmH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = Pitch Bender value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
■
Channel Mode Messages
●
All Sounds Off (Controller number 120)
Status 2nd byte 3rd byte
BnH 78H 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When this message is received, all notes currently sounding on the
corresponding channel will be turned off.
●
Reset All Controllers (Controller number 121)
Status 2nd byte 3rd byte
BnH 79H 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When this message is received, all controllers on the corresponding channel will
be set to their reset values.
■
MONO (Controller number 126)
Status 2nd byte 3rd byte
BnH 7EH mmH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = mono number: 00H - 10H (0 - 16)
MONO mode, each message is recognized on the channel shown below.
Message Control in MIDI function
B.CH G.CH
Note on/off individual
Control Change basic Global
Mode Message basic Global
Program Change basic Global
Aftertouch basic Global
Pitch Bender Change individual
Exclusive basic Global
vc1_e.book 142 ページ ２００４年４月２日 金曜日 午後３時２１分