Roland V-Card VC-1, Owner'S Manual

Page: 141 / 156

141
MIDI Implementation
■
Channel Mode Messages
●
All Sounds Off (Controller number 120) (for VariOS only)
Status 2nd byte 3rd byte
BnH 78H 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
●
Reset All Controllers (Controller number 121) (for VariOS only)
Status 2nd byte 3rd byte
BnH 79H 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
●
OMNI OFF (Controller number 124) (for V-Synth only)
Status 2nd byte 3rd byte
BnH 7CH 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
●
POLY (Controller number 127) (for V-Synth only)
Status 2nd byte 3rd byte
BnH 7FH 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
■
System Realtime Messages
●
Active Sensing
Status
FEH
* This message is transmitted at intervals of approximately 250 msec.
●
System Exclusive Messages
Status
F0H
:System Exclusive
F7H :EOX (End Of Exclusive)
Transmitted in the following three cases.
1.
When Operating Bulk-Dump
2. If Exclusive of System MIDI is “P-Dump,” this unit transmits all parameters
in the patch when the patch is changed.
3. If Exclusive of System MIDI is “TxEdit,” this unit transmits the parameter
when the parameter is edited.
Refer to Section 3 to see details.
2. Receive data
■
Channel Voice Messages
●
Note off
Status 2nd byte 3rd byte
8nH kkH vvH
9nH kkH 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = note off velocity: 00H - 7FH (0 - 127)
●
Note on
Status 2nd byte 3rd byte
9nH kkH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = note on velocity: 01H - 7FH (1 - 127)
●
Control Change
m Bank Select (Controller number 0, 32)
Status 2nd byte 3rd byte
BnH 00H mmH
BnH 20H llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)
* Not received when the Bank Select Switch (SYSTEM MIDI) is OFF.
* The Patches corresponding to each Bank Select are as follows.
* The MSB value to be transmitted can be set individually for
* each patch using Tx Bank Select (PATCH MIDI).
* In this case, “0” is always output for the LSB.
❍
Modulation (Controller number 1)
Status 2nd byte 3rd byte
BnH 01H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Modulation depth: 00H - 7FH (0 - 127)
BANK
SELECT
MSB LSB
PROGRAM
NUMBER
BATCH
BANK
PATCH
NUMBER
087
000 001 - 064 Internal 1 11 - 88
001 001 - 064 Internal 2 11 - 88
002 001 - 064 Internal 3 11 - 88
003 001 - 064 Internal 4 11 - 88
004 001 - 064 Internal 5 11 - 88
005 001 - 064 Internal 6 11 - 88
006 001 - 064 Internal 7 11 - 88
007 001 - 064 Internal 8 11 - 88
008 001 - 064 Preset 1 11 - 88
009 001 - 064 Preset 2 11 - 88
010 001 - 064 Preset 3 11 - 88
011 001 - 064 Preset 4 11 - 88
012 001 - 064 Preset 5 11 - 88
013 001 - 064 Preset 6 11 - 88
vc1_e.book 141 ページ ２００４年４月２日 金曜日 午後３時２１分