Appendix
48
STEP PHASER
This is a stereo phaser. The phaser effect is varied gradually in steps.
Parameter
Value
Explanation
Mode
4-STAGE,
8-STAGE, 12-STAGE Number of stages in the phaser
Manual
0–127
Center frequency from which the sound is
modulated
Rate Sync Sw
OFF, ON
Sets whether the modulation rate is specified
as a note value (ON) or not (OFF).
Rate
0.05–10.00
[Hz]
,
note
Frequency of modulation
Depth
0–127
Depth of modulation
Polarity
INVERSE,
SYNCHRO
This sets the left/right modulation phase.
INVERSE:
left/right phases inverted
When using a mono source, this gives the
sound a more spread-out feel.
SYNCHRO:
left/right phases synchronized
Select this when inputting a stereo source.
Resonance
0–127
Amount of feedback
Cross Feedback
-98–+98
[%]
Adjusts the proportion of the phaser sound
that is fed back into the effect. (Negative values
invert the phase.)
Step Rate Sync Sw
OFF, ON
Sets whether the modulation rate of the
phaser effect is specified as a note value (ON)
or not (OFF).
Step Rate
0.10–20.00
[Hz]
,
note
Rate of the step-wise change in the phaser
effect
Low Gain
-15–+15
[dB]
Amount of low range boost/cut
High Gain
-15–+15
[dB]
Amount of high range boost/cut
Level
0–127
Output level
FLANGER
This is a stereo flanger. (The left/right phases of the LFO are
synchronized.)
The effect produces a metallic resonance that rises and falls like a jet
airplane taking off or landing. A filter is provided so that you can adjust
the timbre of the flanged sound.
Parameter
Value
Explanation
Filter Type
OFF, LPF, HPF
Filter type
OFF:
Filter is not used
LPF:
High frequencies at or above the cutoff
value are filtered
HPF:
Low frequencies at or below the cutoff
value are filtered
Cutoff Freq
200–8000
[Hz]
Center frequency at which the filter cuts a
specific frequency region
Pre Delay
0.0–100.0
[ms]
Adjusts the delay time from when the direct
sound begins until the flanger sound is heard.
Tempo Sync Sw
OFF, ON
Sets whether the modulation rate is specified
as a note value (ON) or not (OFF).
Rate
0.05–10.00
[Hz]
,
note
Rate of modulation
Depth
0–127
Depth of modulation
Phase
0–180
[deg]
Spatial spread (depth) of the flanger sound
Feedback
-98–+98
[%]
Adjusts the proportion of the flanger sound
that is fed back into the effect. (Negative values
invert the phase.)
Low Gain
-15–+15
[dB]
Amount of low range boost/cut
High Gain
-15–+15
[dB]
Amount of high range boost/cut
Level
0–127
Output level
REVERB
Adds reverberation to the direct sound, simulating an acoustic space.
Parameter
Value
Explanation
Type
ROOM1,
ROOM2, STAGE1,
STAGE2, HALL1,
HALL2
Reverb type
Pre Delay
0.0–100
[msec]
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Time
0–127
Time length of reverberation
HF Damp
200–8000
[Hz]
,
BYPASS
Center frequency at which the high-frequency
content of the reverb sound is cut (BYPASS:
no cut)
Low Gain
-15–+15
[dB]
Amount of low range boost/cut
High Gain
-15–+15
[dB]
Amount of high range boost/cut
Level
0–127
Output level
Summary of Contents for TAIKO-1
Page 1: ...2021 Roland Corporation 01...