Appendix
46
REVERSE DELAY
This is a reverse delay that adds a reversed and delayed sound to the
input sound. A tap delay is connected immediately after the reverse
delay.
Parameter
Value
Explanation
Threshold
0–127
Volume at which the reverse delay begins to
be applied
Tempo Sync
Rev Sw
OFF, ON
Sets whether the delay time value of the
reverse delay is specified as a note value (ON)
or not (OFF).
Rev Delay
Time
1–1300
[msec]
,
note
Delay time from when sound is input into the
reverse delay until the delay sound is heard
Rev Delay
Feedback
-98–+98
[%]
Proportion of the delay sound that is returned
to the input of the reverse delay (negative
values invert the phase).
Rev Delay
HFDamp
200–8000
[Hz]
,
BYPASS
Center frequency at which the high
frequencies of the reverse delay are cut
(set this to BYPASS if you do not want to cut
the frequencies)
Rev Delay Pan
L64–R63
Stereo position of the reverse delay sound
Rev Delay
Level
0–127
Volume of the reverse delay sound
Tempo Sync
Delay 1
–
3
OFF, ON
Sets whether the delay time value of the tap
delay is specified as a note value (ON) or not
(OFF).
Delay 1
–
3
Time
1–1300
[msec]
,
note
Delay time from when sound is input into the
tap delay until the delay sound is heard
Delay 3
Feedback
-98–+98
[%]
Proportion of the delay sound that is returned
to the input of the tap delay (negative values
invert the phase)
Delay HF
Damp
200–8000
[Hz]
,
BYPASS
Center frequency at which the high
frequencies of the tap delay are cut
(set this to BYPASS if you do not want to cut
the frequencies)
Delay 1 Pan
,
Delay 2 Pan
L64–R63
Stereo position of the tap delay sounds
Delay 1 Level
,
Delay 2 Level
0–127
Volume of the tap delay sounds
Low Gain
-15–+15
[dB]
Amount of low range boost/cut
High Gain
-15–+15
[dB]
Amount of high range boost/cut
Level
0–127
Output level
3TAP PAN DELAY
Produces three delay sounds; center, left and right.
Parameter
Value
Explanation
Tempo Sync L
,
R
,
C Sw
OFF, ON
Sets whether the delay time value of the left/
right/center delay sound is specified as a note
value (ON) or not (OFF).
Delay L
,
R
,
C
Time
1–2600
[msec]
,
note
Time after the direct sound until the left/right/
center delay sounds are heard
Center
Feedback
-98–+98
[%]
The amount of delay sound fed back to the
input.
(Negative values invert the phase.)
HF Damp
200–8000
[Hz]
,
BYPASS
Center frequency at which the high
frequencies of the delay sound fed back to the
input are cut
(set this to BYPASS if you do not want to cut
the frequencies)
Left
,
Right
,
Center Level
0–127
Volume of the left/center/right delay sounds
Low Gain
-15–+15
[dB]
Amount of low range boost/cut
High Gain
-15–+15
[dB]
Amount of high range boost/cut
Level
0–127
Output level
SHELL RESONANCE
Adds a resonating sound to the sound of the taiko head.
Parameter
Value
Explanation
Type
1–5
Selects the type of resonance.
Level
0–127
Adjusts the output volume.
OD
0
DELAY
Parameter
Value
Explanation
Overdrive Drive
0–127
The degree of distortion.
Also changes the volume.
Overdrive Pan
L64–R63
Stereo position of the overdrive sound
Tempo Sync Sw
OFF, ON
Sets whether the delay time value of the delay
is specified as a note value (ON) or not (OFF).
Delay Time
1–2600
[msec]
,
note
Adjusts the delay time from the direct sound
until the delay sound is heard.
Delay Feedback
-98–+98
[%]
Adjusts the proportion of the delay sound that
is fed back into the effect. (Negative values
invert the phase.)
Delay HF Damp
200–8000
[Hz]
,
BYPASS
The frequency above which the delay sound
fed back to the input is cut. If you do not want
to cut the high frequencies, set this parameter
to BYPASS.
Delay Balance
D100:0W–
D0:100W
Volume balance between the sound that is
sent through the delay (W) and the sound that
is not sent through the delay (D)
Level
0–127
Output level
DS
0
DELAY
The parameters are essentially the same as in “OD
0
DELAY,” with the
exception of the following two.
Overdrive Drive
0
Distortion Drive, Overdrive Pan
0
Distortion Pan
Summary of Contents for TAIKO-1
Page 1: ...2021 Roland Corporation 01...