75
Parameter List
Drum Kit Tone Parameters
(Drum)
SOUND
Parameter
Value
Explanation
Level
0–127
Adjusts the overall volume of the tone
MFX
Parameter
Value
Explanation
Type
Selects the MFX type.
Switch
OFF, ON
Switches the MFX on/off.
Chorus Send Level
0–127
Adjusts the amount of chorus.
If you don’t want to add the chorus effect, set
it to 0.
Reverb Send Level
0–127
Adjusts the amount of reverb.
If you don’t want to add the reverb effect, set
it to 0.
MFX parameters
Edit the parameters for the selected MFX. The available parameters
differ depending on the type of the effects you selected in MFX Type.
&
KIT MFX CTRL
Parameter
Value
Explanation
Control 1–4 Source
Specifies the MIDI message that will control the corresponding MFX
CONTROL parameter.
OFF
MFX will not be used.
CC01–31
Controller number 1–31
CC33–95
Controller number 33–95
BEND
Pitch Bend
AFT
Aftertouch
SYS-CTRL1–4
Use the controller that is assigned by the
System Control Source 1–4.
Control 1–4
Destination
Specifies which of the multi-effect parameters
are controlled using MFX CONTROL. The
multi-effects parameters available for control
will depend on the multi-effects type.
Control 1–4 Sens
-63–+63
Specifies the depth of MFX CONTROL.
Specify a positive “+” value if you want to
change the value of the assigned destination
in a positive direction (larger, toward the
right, faster, etc.), or specify a negative value
“-” if you want to change the value in a
negative direction (smaller, toward the left,
slower, etc.). Larger values will allow a greater
amount of control.
DRUM COMP1–6
* Only a drum track with compressors can use KIT COMP.
Parameter
Value
Explanation
Switch
OFF, ON
Compressor on/off
Attack Time
0.1–100ms
Time from when the input exceeds the
threshold until compression begins
Release Time
10–1000ms
Time from when the input falls below the
threshold until compression is turned off
Threshold
-60–0 [dB]
Level at which compression is applied
Ratio
1: 1–inf:
1
Compression ratio
Knee
0–30 [dB]
This is a function that smooths the onset of
compression from the uncompressed state; it
gradually applies compression starting earlier
than Threshold. Higher values produce a
smoother transition.
Output Gain
-24–+24 [dB]
Level of the output sound
Output Assign
DRY, MFX
Specifies the compressor output destination.
PAD CTRL
Parameter
Value
Explanation
Level
0–127
Adjusts the volume of the key.
Pan
L64–0–63R
Adjusts the stereo location of the key.
Delay Send Level
0–127
Adjusts the amount of delay for each key.
Reveb Send Level
0–127
Adjusts the amount of reverb for each key.
Mute Group
OFF, 1–31
On an actual acoustic drum set, an open hi-
hat and a closed hi-hat sound can never
occur simultaneously.
To reproduce the reality of this situation, you
can set up a Mute Group.
The Mute Group function allows you to
designate two or more keys that are not
allowed to sound simultaneously. Up to 31
Mute Groups can be used.
Keys that are not belong to any such group
should be set to “OFF.”
Output Assign
DRY, MFX,
COMP1–6
Specifies the output destination for each key.
Key Offset
-24–+24
Shifts the pitch in units of a semitone.
Fine Tune Offset
-50–+50 [cent]
Finely adjusts the pitch in units of one cent.
TVC Cutoff Offset
-100–+100
Adjusts how far the filter is open.
Increasing this value makes the sound
brighter, and decreasing it makes the sound
darker.
TVF Resonance
OffSet
-100–+100
Emphasizes the portion of the sound in
the region of the cutoff frequency, adding
character to the sound. Excessively high
settings can produce oscillation, causing the
sound to distort.
Increasing this value strengthens the
character, and decreasing it weakens the
character.
TVA Attack Time
Offset
-100–+100
Adjusts the time over which the sound
reaches its maximum volume after you press
the key.
Larger settings of this value make the attack
gentler, and smaller settings make the attack
sharper.
TVA Decay Time
Offset
-100–+100
Adjusts the time over which the volume
decreases from its maximum value.
Larger settings of this value make the decay
longer, and smaller settings make the decay
shorter.
TVA Release Time
Offset
-100–+100
The time it takes after the key is released for a
sound to become inaudible.
If Envelope Mode is NO-SUS, this is the time
until the sounded note becomes inaudible.
Larger settings of this value make the sound
linger, and smaller settings make the sound
end more sharply.
PAD EQ
Parameter
Value
Explanation
EQ Switch
OFF, ON
Turns the equalizer on/off for each key.
EQ Low Gain
-24.0–+24.0 [dB]
Gain of the low frequency range.
EQ Mid Gain
-24.0–+24.0 [dB]
Specifies the reference frequency of the mid-
frequency range.
EQ High Gain
-24.0–+24.0 [dB]
Gain of the high frequency range.
EQ Low Frequency
20–16000 [Hz]
Frequency of the low range.
EQ Mid Frequency
20–16000 [Hz]
Adjusts the amount of mid-frequency boost/
cut.
EQ High Frequency
20–16000 [Hz]
Frequency of the high range.
Mid Q
0.5–16.0 (0.1step)
Specifies the width of the mid-frequency
range.
Set a higher value for Q to narrow the range
to be affected.
