ROHS MC9S08QE128 Reference Manual Download Page 244 | Manualshive

Page: 244 / 345

background image

Real-Time Counter (S08RTCV1)

MC9S08QE128 MCU Series Reference Manual, Rev. 2

244

Freescale Semiconductor

13.4

Functional Description

The RTC is composed of a main 8-bit up-counter with an 8-bit modulo register, a clock source selector,
and a prescaler block with binary-based and decimal-based selectable values. The module also contains
software selectable interrupt logic.

After any MCU reset, the counter is stopped and reset to 0x00, the modulus register is set to 0x00, and the
prescaler is off. The 1-kHz internal oscillator clock is selected as the default clock source. To start the
prescaler, write any value other than zero to the prescaler select bits (RTCPS).

Three clock sources are software selectable: the low power oscillator clock (LPO), the external clock
(ERCLK) and the internal clock (IRCLK). The RTC clock select bits (RTCLKS) are used to select the
desired clock source. If a different value is written to RTCLKS, the prescaler and RTCCNT counters are
reset to 0x00.

RTCPS and the RTCLKS[0] bit select the desired divide-by value. If a different value is written to RTCPS,
the prescaler and RTCCNT counters are reset to 0x00.

shows different prescaler period values.

Table 13-6. Prescaler Period

RTCPS

1-kHz internal clock

source prescaler period

(RTCLKS = 00)

1-MHz external clock

source prescaler period

(RTCLKS = 01)

32-kHz internal clock

source prescaler period

(RTCLKS = 10)

32-kHz internal clock

source prescaler period

(RTCLKS = 11)

0000

Off

Off

Off

Off

0001

8 ms

1.024 ms

250

μ

s

32 ms

0010

32 ms

2.048 ms

1 ms

64 ms

0011

64 ms

4.096 ms

2 ms

128 ms

0100

128 ms

8.192 ms

4 ms

256 ms

0101

256 ms

16.4 ms

8 ms

512 ms

0110

512 ms

32.8 ms

16 ms

1.024 s

0111

1.024 s

65.5 ms

32 ms

2.048 s

1000

1 ms

1 ms

31.25

μ

s

31.25 ms

1001

2 ms

2 ms

62.5

μ

s

62.5 ms

1010

4 ms

5 ms

125

μ

s

156.25 ms

1011

10 ms

10 ms

312.5

μ

s

312.5 ms

1100

16 ms

20 ms

0.5 ms

0.625 s

1101

0.1 s

50 ms

3.125 ms

1.5625 s

1110

0.5 s

0.1 s

15.625 ms

3.125 s

1111

1 s

0.2 s

31.25 ms

6.25 s

«
...
242
243
244
245
246
...
»

Summary of Contents for MC9S08QE128


























































































































































































































































































































































Reviews:

No comments

Related manuals for MC9S08QE128

Brand: Parker Pages: 30

Brand: Calpeda Pages: 4

Brand: Federal Signal Corporation Pages: 79

Brand: Federal Signal Corporation Pages: 32

Brand: jbc Pages: 8

Brand: Netafim Pages: 4

Brand: TREND Pages: 12

Brand: VMK Pages: 98

Brand: Swagelok Pages: 20

Brand: Wilo Pages: 128

Brand: D+H Pages: 16

Brand: CompuPro Pages: 33

Brand: Samson Pages: 182

Brand: Ultraflex Pages: 48

Brand: GCE Pages: 46

Brand: Tusa Pages: 72

Brand: Danfoss Pages: 96

Brand: ETI Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands